Datamate M80 Series Manual Download Page 10

Page: 10 / 15

COMPONENT SPECIFICATION

C00525

- 10 -

APPENDIX 2 – COAX CONTACT DETAILS

A2.1. COAX INTERFACE DIMENSIONS

Male

Female

A2.2. COAX ASSEMBLY INSTRUCTIONS – M80-305/306/307, M80-315/316/317

1) Strip cable to dimensions shown against relevant part (see appropriate engineering drawings).

2) Identify pieces of coax connector to be assembled.

3) Slide sleeve onto cable past stripped area.

4) Crimp contact to end of cable inner conductor.

5) Insert cable and contact into coax body from back end – make sure that the braid goes outside and

over the end section.

6) Slide sleeve back over the end of the coax body and the braid. Crimp into place on the cable

insulation, using a hexagonal crimping tool.

Inner Conductor

Outer Insulator

Body

Sleeve

Contact

Crimp here

Sleeve

Contact

Body

Braid

Crimp here

Inner Insulator

Braid

Summary of Contents for M80 Series
















Search results

Summary of Contents for M80 Series

Reviews:

Related manuals for M80 Series

Brands by name

Popular brands

Datamate M80 Series, Manual

Search results

Summary of Contents for M80 Series

Reviews:

Related manuals for M80 Series

Brands by name

Popular brands