Datalogic Magellan 800i Page 42 Reference Manual Download

Page: 42 / 184

Interface Related Features

Magellan

800i

RS-232 Interface Features — cont.

Beep on ASCII BEL

Enables/disables ability of scanner to beep (sound a good read tone) on receiving an ASCII BEL
(07 hex).

Beep on Not on File

Enables the scanner to cause beep to be sounded on receiving not-on-file (NOF) command.

START / END

PROGRAMMING BAR CODES

Disable Beep on ASCII BEL

DEFAULT

Enable Beep on ASCII BEL

069D00(CR)

069D01(CR)

START / END

PROGRAMMING BAR CODES

Beep on Not On File = Disable

Beep on Not On File = Low Volume

DEFAULT

Beep on Not On File = Medium Volume

Beep on Not On File = High Volume

045100(CR)

045101(CR)

045102(CR)

045103(CR)

Summary of Contents for Magellan 800i

























































































































































































Search results

Summary of Contents for Magellan 800i

Reviews:

Related manuals for Magellan 800i

Brands by name

Popular brands

Datalogic Magellan 800i, Reference Manual

Search results

Summary of Contents for Magellan 800i

Reviews:

Related manuals for Magellan 800i

Brands by name

Popular brands