Datalogic Magellan 800i Page 155 Reference Manual Download

Page: 155 / 184

2D Symbologies

Product Reference Guide

147

Aztec — continued

Aztec Length 1, Length 2 Programming Instructions

1. Scan the START bar code.

2. Scan either the Set Length 1 or Set Length 2 bar code.

3. Turn to

Alphanumeric Pad

and scan the four digits (zero-padded) representing the length.

Scan the END bar code.

NOTE

For Aztec labels, only the data characters are included in the length cal-
culations.

Any value set higher than 3700 will be considered to be 2710.

START / END

PROGRAMMING BAR CODES

DEFAULT SETTING FOR THIS FEATURE: 0001

Set Length 1

Set Length 2

DEFAULT SETTING FOR THIS FEATURE: 2710

0433(CR)

0434(CR)

Summary of Contents for Magellan 800i

























































































































































































Search results

Summary of Contents for Magellan 800i

Reviews:

Related manuals for Magellan 800i

Brands by name

Popular brands

Datalogic Magellan 800i, Reference Manual

Search results

Summary of Contents for Magellan 800i

Reviews:

Related manuals for Magellan 800i

Brands by name

Popular brands