Datakom DKG-209 User Manual Download Page 21

Page: 21 / 53

DKG-209 User Manual V-29

(20.08.2013)

- 21 -

The unit features a non-erasable incremental engine hour meter. The hour meter information is

kept in a non-volatile memory and is not affected from power supply failures.

The engine hours may be displayed

STATISTICAL COUNTERS

menu.

This chapter is intentionally left blank.

Some additional features are installed within consecutive software releases. In order to be

sure of the validity of the status of the unit, the software version needs to be known.

The unit is capable of making modem calls in case of alarm, as well as answering modem

calls made from a remote location.

GSM

modems and classic cable network (

PSTN

) modems are

acceptable.

If the modem is connected to the unit, the

Modem Enable

program parameter should be set

to 1, otherwise faulty operation may occur.

A maximum of 2 telephone numbers can be defined for outgoing modem calls. In case of

alarm, the unit will attempt to reach control centers associated with each number. In case of modem
connection failure, the call will be repeated up to 30 times with 2 minute intervals.

When the modem call is in progress, a telephone icon (

) will appear at the upper right

corner of the screen.

Advised modems are DATAKOM types which are powered up from the same DC battery

voltage than the unit. Most of other desktop modems with standard AT commands are also usable, but
it

is the user’s responsibility to provide an uninterrupted AC supply source to the modem. The

necessary modem cable will be supplied by DATAKOM.

Modem calls are always terminated by the central RAINBOW software. However the unit does

not allow connection durations exceeding 2 minutes, and hangs up the modem when this period
expires.

The PC program used for remote monitoring and programming is the same RAINBOW

software used for RS-232 connection.

Please note that the modem operation is also compatible with the MODBUS communication.

Thus the unit can iniate and receive calls to/from a MODBUS master station. Please review chapter_8
for more details on MODBUS communication.

Modem Enable

SMS Enable

MODBUS Address

parameters are different from zero, the local PC
connection will not work.

6.14 Modem Connection

6.13 Software Version Display

6.12 -

6.11 Engine Hour Meter

Summary of Contents for DKG-209






















































Search results

Summary of Contents for DKG-209

Reviews:

Related manuals for DKG-209

Brands by name

Popular brands

Datakom DKG-209, User Manual

Search results

Summary of Contents for DKG-209

Reviews:

Related manuals for DKG-209

Brands by name

Popular brands