manualshive.com logo in svg

DataDirect Networks EF3015, Setup Manual, Page: 4 / 59

Share
Download
DataDirect Networks EF3015 Setup Manual Download Page 4

E F 3 0 1 5   S e t u p   G u i d e   ( R e v   A )

4

Preface 

This guide provides information about the EF3015 Fibre Channel Controller Enclosure:

The EF3015 isMIL-STD-compliant and supports large form factor (LFF 12-disk) drive 
enclosures — using either AC or DC power supplies.

NOTE :

See 

 "The EF3015 System Components"

 for details regarding enclosure 

components. 

Intended audience

This guide is intended for use by system administrators and technicians who are 
experienced with the following:

• Direct attach storage (DAS) or storage area network (SAN) management

• Network administration

• Network installation

• Storage system installation and configuration

Prerequisites

Prerequisites for installing and configuring this product include familiarity with:

• Servers and computer networks

• Fibre Channel (FC), Serial Attached SCSI (SAS), Internet SCSI (iSCSI), and Ethernet 

protocols 

Related Documentation 

• EF3015 Command Line User Interface (CLUI) Command Reference

• EF3015 Quick Start Guide

• EF3015 Rackmount Bracket Kit Installation Instructions 

• EF3015 RAIDar User Guide 

Summary of Contents for EF3015




























































Reviews:

No comments