DAS MSENS-GY User Manual Download

Page: 23 / 23

3-axis accelerometer & 3-axis gyro sensor

MSENS-GY

User’s manual

Additional Warnings

The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids,

such as vases, shall be placed on apparatus.

L'appareil ne doit pas itre exposi aux ecoulements ou aux edaboussures etaucun objetne

contenantdeliquide, tel qu'un vase, ne doit itre place sur I'objet.

Battery shall not be exposed to excessive heat such as sunshine, fire or the like.

Les piles ne doiventpas itre exposees a de.forte chaleur,

tel qu'a la lumiere du soleil, au feu ou autres choses de

semblable.

Caution marking is located at the rear or back of the apparatus.

Attention marquageestsituea I'arriereou a I'arriere de l'appareil

The marking information is located at the rear or back of apparatus.

Les informations de marquage est situe a I'arriere ou a I'arriere de l'appareil.

DAS Co., Ltd
Copyright ⓒ by Das Co.,Ltd. All Right Reserved

Website      :    www.das-co.com
Phone No :    +82 - (0)31 - 356 - 3541
FAX No      :    +82 - (0)31 – 356 - 3572
e-mail        :      [email protected]
Address    :    09-3, Yangno-ri, Bibong-myeon, Hwaseong-si, Gyeonggi-do, Korea

[445-842]

Summary of Contents for MSENS-GY
























Search results

Summary of Contents for MSENS-GY

Reviews:

Related manuals for MSENS-GY

Brands by name

Popular brands

DAS MSENS-GY, User Manual

Search results

Summary of Contents for MSENS-GY

Reviews:

Related manuals for MSENS-GY

Brands by name

Popular brands