background image

 

 

 

22 

 

  

 

 

COM-42 2Ch Handheld set 

Product code: D1464 

8.

 

Deinstallation, Transportation and Storage 

 

Disconnect power supply before deinstallation. 

 

Use the original packaging to transport the device, if possible. 

 

Clean the device before storing. Follow the cleaning instructions in chapter 7.1.1. Basic Cleaning 
Instructions
 on page 21. 

 

Store the device in the original packaging, if possible. 

9.

 

Disposal 

 

 

Correct disposal of this product 

Waste Electrical and Electronic Equipment 

This symbol on the product, its packaging or documents indicates that the product 
shall not be treated as household waste. Dispose of this product by handing it to the 
respective collection point for recycling of electrical and electronic equipment. This 
is to avoid environmental damage or personal injury due to uncontrolled waste 
disposal. For more detailed information about recycling of this product contact the 
local authorities or the authorized dealer. 

10.

 

Approval 

  

 

Hereby, Highlite International declares that the device COM-24 2Ch Handheld set, product code D1464, 
is in compliance with Directive 2014/53/EU (RED – Radio Equipment Directive). 

The full text of the EU declaration of conformity is available at the respective product page on the 
website of Highlite International (

www.highlite.com

). 

The DAP COM-24 is a Class 2 wireless audio device (Commission Decision 2000/299/EC). 

Frequency: 606–630 MHz 

 

BE 

BG  DE 

LV 

ES 

SE 

Exclusion of liability 

The frequency ranges available for radio transmitters differ per country and region. Consult the 
respective national and/or regional authority as licensing or specific restrictions may apply for the use of 
the device. We do not take any responsibility in case the device cannot operate or cannot be used in 
your country/region or if it requires additional licensing. Before using the device, make sure that the 
frequencies are allowed in your country or region. 

 

 
 

Summary of Contents for COM-42

























Reviews: