Danfoss VLT Micro Drive FC 51 Series Operating Instructions Manual Download Page 8 | Manualshive

Page: 8 / 73

Danfoss VLT Micro Drive FC 51 Series Operating Instructions Manual Download Page 8

1.1.4 General Warning

Warning:

Touching the electrical parts may be fatal - even after the equipment has been disconnected from mains.
Also make sure that other voltage inputs have been disconnected (linkage of DC intermediate circuit).
Be aware that there may be high voltage on the DC link even when the LEDs are turned off.
Before touching any potentially live parts of the frequency converter, wait at least 4 minutes for all sizes.
Shorter time is allowed only if indicated on the nameplate for the specific unit.

Leakage Current

The earth leakage current from the frequency converter exceeds 3.5 mA. According to IEC 61800-5-1 a reinforced Protective Earth
connection must be ensured by means of a min. 10mm² Cu or an addtional PE wire - with the same cable cross section as the Mains
wiring - must be terminated separately.

Residual Current Device

This product can cause a DC current in the protective conductor. Where a residual current device (RCD) is used for extra protection,
only an RCD of Type B (time delayed) shall be used on the supply side of this product. See also Danfoss Application Note on RCD, MN.
90.GX.YY.
Protective earthing of the frequency converter and the use of RCDs must always follow national and local regulations.

Motor overload protection is possible by setting Parameter 1-90 Motor thermal protection to the value ETR trip. For the North American
market: ETR functions provide class 20 motor overload protection, in accordance with NEC.

Installation in high altitudes:

For altitudes above 2 km, please contact Danfoss regarding PELV.

1.1.5 IT Mains

IT Mains

Installation on isolated mains source, i.e. IT mains.
Max. supply voltage allowed when connected to mains: 440 V.

As an option, Danfoss offers line filters for improved harmonics performance.

1.1.6 Avoid unintended Start

While the frequency converter is connected to mains, the motor can be started/stopped using digital commands, bus commands, references or via the
Local Control Panel.

•

Disconnect the frequency converter from mains whenever personal safety considerations make it necessary to avoid unintended start of any
motors.

•

To avoid unintended start, always activate the [OFF] key before changing parameters.

VLT

®

Micro Drive FC 51 Operating Instructions

1 Safety

MG.02.A4.02 - VLT

®

is a registered Danfoss trademark

7

1

«
...
6
7
8
9
10
...
»

Summary of Contents for VLT Micro Drive FC 51 Series










































































Reviews:

No comments