manualshive.com logo in svg

Danfoss VLT Micro Drive FC 51 Series, Operating Instructions Manual, Page: 17 / 73

Share
Download
Danfoss VLT Micro Drive FC 51 Series Operating Instructions Manual Download Page 17

3.6 Power Circuit - Overview

3.6.1 Power Circuit - Overview

Illustration 3.10: Diagram showing all electrical terminals.

Brake not applicable for frame M1.

Brake resistors are available from Danfoss.
Improved power factor and EMC performance can be achieved by installing optional Danfoss line filters.
Danfoss power filters can also be used for load sharing.

 

3.6.2 Load sharing/Brake

Use 6.3 mm insulated Faston Plugs designed for high voltage for DC (Load Sharing and brake).
Contact Danfoss or see instruction no. MI.50.Nx.02 for load sharing and instruction no. MI.90.Fx.02 for brake.

Load sharing: Connect terminals UDC- and UDC/BR+.
Brake: Connect terminals BR- and UDC/BR+.

Note that voltage levels of up to 850 V DC may occur between terminals
UDC+/BR+ and UDC-. Not short circuit protected.

3 Electrical Installation

VLT

®

 Micro Drive FC 51 Operating Instructions

16

MG.02.A4.02 - VLT

®

 is a registered Danfoss trademark

3  

Summary of Contents for VLT Micro Drive FC 51 Series










































































Reviews:

No comments