Danfoss VLT CANopen MCA 105 Programming Manual Download

Page: 47 / 50

8.2.8 EMCY Error Code

(OD: 1003)

Code (hex)

Description

No fault.

1000

General fault.

2130

Short circuit.

2213

Overcurrent during start-up.

2240

Short to ground.

2310

Continuous overcurrent.

2311

Current inside the device.

3100

Mains voltage.

3130

Phase failure.

3210

Overvoltage inside the device.

3220

Undervoltage inside the device.

3300

Output voltage.

4210

Exceed device temperature.

4310

Excess frequency converter temperature.

5110

Low voltage power supply.

5112

+24 V power supply.

5210

Measurement circuit.

6100

Internal software fault.

7110

Brake chopper.

8100

Communication.

8110

CAN overrun (objects lost).

8120

CAN in error (passive mode).

8130

Life Guard error or heartbeat error.

8140

Recovered from Bus Off.

8150

Transmit COB-ID collision.

8210

PDO not processed due to length error.

8220

PDO length exceeded.

8302

Torque limiting.

FFxx

Vendor specific.

Table 8.9 EMCY Error Code

Troubleshooting

Programming Guide

MG92G102

Summary of Contents for VLT CANopen MCA 105


















































Search results

Summary of Contents for VLT CANopen MCA 105

Reviews:

Related manuals for VLT CANopen MCA 105

Brands by name

Popular brands

Danfoss VLT CANopen MCA 105, Programming Manual

Search results

Summary of Contents for VLT CANopen MCA 105

Reviews:

Related manuals for VLT CANopen MCA 105

Brands by name

Popular brands