Danfoss Series 45 Service Manual Download Page 15 | Manualshive

Page: 15 / 44

Danfoss Series 45 Service Manual Download Page 15

Pressure drop across external control valve defines system demand

Cross-section LS control

Spool

Spring
guide

Spring

LS adjusting
plug

LS spring

PC adjusting
plug

Plug

Plug

Spool

Spring
guide

Spring
(PC heavy)

P104 051

LS spool shifts to port system pressure to servo piston

Electric Proportional Controls
Plus+1

TM

Compliance

All Series 45 Electric controls have met and passed the Danfoss PLUS+1

®

compliance standard testing,

and as such, this Series 45 control is PLUS+1

®

compliant. PLUS+1

®

compliance blocks are available on the

Danfoss website, within the PLUS+1 Guide section.
Electric Proportional Control Principle

The Electric Proportional Control consists of a proportional solenoid integrated into a Remote Pressure
Compensated control. This control allows the pump to be operated at any pressure limit between the
Load Sense and Pressure Compensation settings by varying the current sent to the solenoid.

Electric On/Off Controls
PLUS+1

TM

Compliance

All Series 45 Electric controls have met and passed the Danfoss PLUS+1

®

compliance standard testing,

and as such, this Series 45 control is PLUS+1

®

compliant. PLUS+1

®

compliance blocks are available on the

Danfoss website, within the PLUS+1 Guide section.

Service Manual

Series 45 E Frame Open Circuit Pumps

Features

©

Danfoss | September 2016

AX00000024en-US0401 | 15

«
...
13
14
15
16
17
...
»

Summary of Contents for Series 45













































Reviews:

No comments