Danfoss Series 45 Service Manual Download Page 38 | Manualshive

Page: 38 / 44

Danfoss Series 45 Service Manual Download Page 38

5. Check magnet carrier for cracks , deformations, wearing, and for contamination with magnetic

particles

W

Warning

A thorough inspection with the angle sensor removed is a strong indicator of pump and hydraulic

system contamination and filtration quality.

Reassembly

1. Using new magnet carrier screws with locking compound (K115) install the magnet carrier (K105) to

pump swashplate through the housing. Torque the screws to 4.5 Nm [3.3 lbf-ft].

W

Warning

Used magnet carrier screws may loosen and lead to premature failure. Ensure that new screws with

locking compound are utilized.

2. Install the locating dowels (K185) into the dowel holes.
3. Lubricate new O-ring (K175) with petroleum jelly. Install the O-ring to the angle sensor housing

(K265) first.

4. Install angle sensor housing (K265) with O-ring (K175) to housing with 4 screws (K195) and torque to

5.9 Nm [4.4 lbf-ft].

Service Manual

Series 45 E Frame Open Circuit Pumps

Minor repair

38 |

©

Danfoss | September 2016

AX00000024en-US0401

«
...
36
37
38
39
40
...
»

Summary of Contents for Series 45













































Reviews:

No comments