Danfoss PVG 32 Technical Information Download Page 31

Page: 31 / 76

PVE characteristic - control by voltage

PVEP

control range

PVEU

fixed

7.5V

2.5V

Closed loop control

The PVE variants PVEA/H/M/S/U/P and the PVED-CC/-CX has a closed loop control supported by a spool
position sensor that ensures integrity towards flow forces and oil viscosity.

Hysteresus for PVE variants*

20%

PVEM

PVEA

-2

-4

-6

-8

PVEH

157-504.10

PVES

~0%

* Hysteresis (control signal/spool travel) is indicated at rated voltage and f = 0.02 Hz. (one cycle = neutral

→

full A

→

full B

→

neutral)

The standard PVE’s are proportional activated actuator except PVEO which is on/off. The PVE’s have fault-
monitoring.

•

PVEU is available with PVEH and PVES hysteresis

•

PVEP, PVED-CC and PVED-CX are available with PVES hysteresis

The values are typical test data for exact ranges, see

PVE Technical Information

, 520L0553.

Technical Information

PVG 32 Proportional Valve Group

Electrical actuation

Danfoss | August 2017

520L0344 | BC00000038en-US0802 | 31

Summary of Contents for PVG 32













































































Search results

Summary of Contents for PVG 32

Reviews:

Related manuals for PVG 32

Brands by name

Popular brands

Danfoss PVG 32, Technical Information

Search results

Summary of Contents for PVG 32

Reviews:

Related manuals for PVG 32

Brands by name

Popular brands