background image

Ordering information

To build a complete tandem, one must order the 
2 compressors and 1 manifolding kit 7777041 
plus 2 mounting kit 7777045.
To build a trio, one must order 3 compressors and 
1 trio manifolding kit 7777049 plus 3 mounting 
kit 7777045.

To build a quadro, one must order 4 compressors 
and 2 manifolding kit 7777041 plus 4 mounting 
kit 7777045. For mounting kit 7777045, please 
refer to guideline section “spare parts & 
accessories” mounting hardware.

Manifolding compressors

Combination

Manifolding kit 

code number

Ordering number Mounting kit code 

number

Ordering number

Even tandem with  passive system

7777041

1

7777045

2

Even tandem with  active system

7777045

2

Even trio with  active system

7777049

1

7777045

3

Even quadro with  active system

7777041

2

7777045

4

Kit code number 7777041

Kit code number 7777049

Designation

Qty

Grommet Sleeves M

6

Flat Washers LL10Z

6

Washers

6

Washer for tandem/quadro

6

Grommets

6

Sleeve 2"1/4 Rotolock - 1"3/8 ODF

2

Teflon seal Φ 50.8 mm

2

Designation

Qty

Grommet Sleeves M

8

Flat Washers LL10Z

8

Washers

8

Washer for trio

8

Grommets

8

Sleeve 2"1/4 Rotolock - 1"5/8 ODF

3

Teflon seal Φ 50.8 mm

3

Note: for kit 7777041, item 6-7 are not needed for active manifolding. please leave these when assemble.

Note: for kit 7777049, items 6-7 are not needed for active manifolding. Please leave these when assembling.

51

FRCC.PC.035.A4.02

Application Guidelines

Manifold compressors

Summary of Contents for MLM116





























































Reviews: