Danfoss MLM116 Application Manuallines Download Page 53

Page: 53 / 60

Tandem unit MLM/MLZ116

Passive system

Compressor mounting

Passive system (50 Hz)

Note: the dimensions are external diameters .The compressors shown here are brazed version, but could also work with rotolock

version.

1"1/8

1"5/8

(2x)

1"1/8

4"1/8

The tandem is fixed on the frame by using
grommet sleeves



, flat washers



, washers



and



and the grommets



, provided in kit

7777041.











HM10 x 100

Supplied with the kit 7777045
Included in kit 7777041
Not supplied

The level of oil naturally balances by a pipe of
1”3/8. To fix this oil connection equalization
Rotolock, the adaptor sleeves



: 2”1/4 - 1”3/8

and Teflon seals



, included in kit 7777041 must

be used.

Oil equalization

connection





Tightening

torque 145 Nm

FRCC.PC.035.A4.02

Application Guidelines

Manifold compressors

Summary of Contents for MLM116





























































Search results

Summary of Contents for MLM116

Reviews:

Related manuals for MLM116

Brands by name

Popular brands

Danfoss MLM116, Application Manuallines

Search results

Summary of Contents for MLM116

Reviews:

Related manuals for MLM116

Brands by name

Popular brands