manualshive.com logo in svg

Danfoss FC 100, Operating Instructions Manual, Page: 16 / 68

Share
Download
Danfoss FC 100 Operating Instructions Manual Download Page 16

4.1.8 LED Behaviour

MS: Service LED (red)

Situation

LED

Description

Configured state (Nornal operation)

½ sec. ON, then continously OFF

The node is configures and running nor-
mally

Non configures state

Flashing ½ Hz

Node is not configures but has an appli-
cation. Proceed with loading node.

Applicationlessstate

1 sec. ON, 2 sec. OFF, then continuosly
ON

Node has no application, the LonWorks
option needs replacing or reprogram-
ming

Watchdog resets

Short flash about each 3 sec.

Indicates problem with application. The
LonWorks option needs replacing

Faulty hardware

Steady ON or OFF

The LonWorks option needs replacing

NS: Status LED (green)

Situation

LED

Description

Node configured

Steady ON

The node is configures and running
normally

Wink sevice

Flashing ½ Hz for 20 sec.

Wink service activated in order to
identify node.

VLT® FC 100 LonWorks

4 How to install

MG.11.E2.02 - VLT

®

 is a registered Danfoss trademark

15

  4

Summary of Contents for FC 100





































































Reviews:

No comments