Danfoss ERC 213 Installation Manual Download Page 9

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products 

already on order provided that such alterations can be made without subsequential changes being necessary

eady agreed.

All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.

Contact info.:
www.danfoss.com/erc

DKRCE.PI.RL0.O2.02 / 520H11062 | 9

© Copyright Danfoss | Published by AZ | 2016.04

Installation guide | ERC 213

Installation guide - ERC 213

EU design registration

Safety standards

Check the input voltage is correct before connecting the instrument.
Do not expose to water or damp: only use the regulator within the design operating limits, avoiding sudden temperature 
changes with high atmospheric humidity to prevent condensate forming.

Product disposal

The device (or product) must be disposed of in compliance with local waste disposal legislation.

002566703-0001

Parameter Name - ERC 213

Code

Min

Max

Unit

App. 0

(Def.)

App. 1 App. 2 App. 3 App. 4 App. 5 App. 6

Readouts

u--

Controller Status 

S0=cooling ON/Heating ON, 
S2=wait for compressor ON time to 
elapse, S3=wait for compressor OFF 
time to elapse-restart time, S4=drip 
OFF delay after defrost, 
S10=cooling stop S11=cooling 
stopped by thermostat / heating OFF, 
S14=defrosting state, 
S15=fan delay state after defrost, 
S17=door open (DI input), 
S20=emergency cooling, S25=manual 
control of outputs, 
S30=continous cycle / Pull-down, 
S32=delay of outputs at power up

u00

S0

S32

--

Air temperature (Sair)

u01

-100.0

200.0

C/F

---

Read the present regulation 
reference

u02

-100.0

200.0

C/F

---

Defrost temperature (S5)

u09

-100.0

200.0

C/F

---

-

-

-

DI1 input

u10

oFF

on

---

Status of night operation

u13

oFF

on

---

DI2 input

u37

oFF

on

---

Condenser temperature (Sc)

U09

-100.0

200.0

C/F

---

Compressor relay status

u58

oFF

on

---

Fan relay status

u59

oFF

on

---

Defrost relay status

u60

oFF

on

---

Light relay status

u63

oFF

on

---

Firmware version readout

u80

000

999

---

Alarm status

Sair air temperature sensor error

E29

S5 defrost sensor error

E27

Sc condenser sensor error

E30

High temperature alarm

A01

Low temperature alarm

A02

High voltage alarm

A99

Low voltage alarm

AA1

Condenser alarm

A61

Door alarm

A04

Standby alarm

A45

DI external alarm

A15

N.B.: hidden parameters are greyed out

Summary of Contents for ERC 213










Reviews: