Danfoss EIM 336, Manual, Page: 13 / 17

© Danfoss A/S (AC-MCI / sw), 2014-11 DKRCC.PS.RQ0.B7.02 /520H8832 13
Manual Superheat Controller EIM 336
Group PNU Parameter Symbolic name Min. Max. Default Units e2 W *10 Description
MOP 3013 n11 MOP 0 200 13.7
bar
(abs.)
ü ü ü
Maximum operation pressure. If Pe goes
above this value, the controller will
control on Pe, and not on superheat
3113 KpM Kp MOP 0.5 10 0.5
ü ü ü
Kp proportional gain while in MOP
control mode
3114 TnM Tn Mop 30 600 180
ü ü
Tn integration time while in MOP control
mode
3121 DMO Diff MOP -20 0 0
bar
(abs.)
ü ü
Differential MOP. A remote offset that is
added to the MOP. Needs to be written
every 5 seconds, else the offset is set
to 0.
Defrost
50011 DeA Def Activate 0 1 0
ü
Defrost activating
50008 DHO Def Hold OD 0 100 30 %
ü ü
Defrost holding level
50009 DH1 Def Hold Ti 1 0 32000 120 s ü ü Defrost holding timer 1
50010 DH2 Def Hold Ti 2 0 32000 60 s
ü ü
Defrost holding timer 2
64305 DDO
Def hold OD
shdw
0 100 30 %
ü ü
Copy of 50008. If it is required to write
Def Hold OD frequently, this should be
used instead.
T
e
Control
3115 KpTe Kp Te 0.5 10 1 ü ü
Kp proportional gain while in Te control
mode
3116 TnT Tn Te 30 600 60
ü ü
Tn integration time while in Te control
mode
3117 TeR Te Reference -200 200 0 °C
ü ü
Te reference while in Te control mode
External
sensors
2643 PEV
ext. EvapPress
P0
0 65535 0
milli
bar
ü
External evaporator pressure. This value
can be used instead of a sensor. This
register must be written at least every 5
seconds, otherwise the sensor value will
be used.
2644 TS2 ext. S2 temp -200 200 0 °C
ü ü
External S2. This value can be used
instead of a sensor. This register must
be written at least every 5 seconds,
otherwise the sensor value will be used.
2646 TS4 ext. S4 Air temp -200 200 0 °C ü ü
External S4. This value can be used
instead of a sensor. This register must
be written at least every 5 seconds,
otherwise the sensor value will be used.
LOC
50003 LTR LOC Trig 0 100 95 %
ü ü
Trigger value for loss of charge
50004 LRe LOC Reset 0 100 85 %
ü ü
Reset value for loss of charge
50005 LTm LOC Timer 0 7200 3600 s
ü ü
Timer to trigger LOC alarm
50007 LST LOC SH Trig 0 50 20 K
ü ü ü
SH error trigger level for LOC alarm
Setup
Modbus
2008 003 Unit Addr 1 240 165
ü ü
Primary unit address is used when
jumper KM7 is mounted
2009 UA2 Unit Addr 2 1 240 164 ü ü
Secondary unit address is used when the
jumper KM7 is not mounted
50060 MBa MB Baud 0 2 1
ü ü
Communication setting baud rate, 0
=9600 , 1 = 19200, 2 = 38400
50061 MPa MB Parity 0 2 2 ü ü
Communication setting parity,
0 = no parity, 1 = odd parity, 2 = even
50062 MSB MB StopB 1 2 1
ü ü
Communication setting stop bit, 1 = 1
stop bit, 2 = 2 stop bit
64200
-
Modbus trans 0 3 1 ü ü
1 = Enabling translation tables. If
the translation table is enabled, only
registers some are accessible.
Valve
3032 n37 Max steps 100 1000 384
ü ü
Maximum number of steps
(384 x 10 microsteps = 480 half steps)
3033 n38 Max steps/sec 5 300 31 ü ü Steps per second
3034 n39 Start backlash 1 100 10 %
ü ü
Backlash (steps) to close in percent at
startup (power on).
3035 n40 Backlash 0 100 20 %
ü ü
Backlash (steps) for spindle play
compensation. This is active during
normal control
3037 n42 Comp. dir. 1 2 1
ü ü
Compensation direction
3051 n56 Motor current 0 300 150 mA
ü ü
Motor current
Regulation
(continued)