Danfoss EC-LTS1200-410 User Manual Download

Page: 33 / 41

Control signal connector information

Description

Part number

Supplier example

X2 temperature measurement connector M16 male

7.840.200.000

www.hummel.com

Insert 10-pole

insert: 7.003.910.101

Pin: 7.010.981.001

Mating connector M16 female

7.810.400.000

Insert 10-pole, M16, RCPT

7.003.910.102

Sensor Connector Socket

7.010.981.002

M16 connector

Pin configuration of temperature measurements (M16 connector, one sensor per inductor)

PIN

Description

Temperature 1, PT100 (P), inductor

Temperature 1, PT100 (N), inductor

Temperature 2, PT100 (P), inductor

Temperature 2, PT100 (N), inductor

Temperature 3, PT100 (P), inductor

Temperature 3, PT100 (N), inductor

Enclosure ground (shield)

Reserve

User Guide

EC-LTS1200-410

Installation

Danfoss | July 2021

BC355449988603en-000201 | 33

Summary of Contents for EC-LTS1200-410










































Search results

Summary of Contents for EC-LTS1200-410

Reviews:

Related manuals for EC-LTS1200-410

Brands by name

Popular brands

Danfoss EC-LTS1200-410, User Manual

Search results

Summary of Contents for EC-LTS1200-410

Reviews:

Related manuals for EC-LTS1200-410

Brands by name

Popular brands