background image

DEVIreg™ 530M

Installation Guide

2

1 Introduction   �  �  �  �  �  �  �  �  �  �  �  �  �  �  �  �  �  �  �  �  �  2

1.1 

Technical Specifications   .  .  .  .  .  .  .  .  .  .  . 3

1.1 

Safety instructions .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 4

Mounting instructions �  �  �  �  �  �  �  �  �  �  �  �  �  �  �  5

3 Settings   �  �  �  �  �  �  �  �  �  �  �  �  �  �  �  �  �  �  �  �  �  �  �  �  8

4 Warranty�  �  �  �  �  �  �  �  �  �  �  �  �  �  �  �  �  �  �  �  �  �  �  10

Disposal Instruction   �  �  �  �  �  �  �  �  �  �  �  �  �  �  �  13

Introduction

DEVIreg™ 530M is an electronic thermostat provided with a 

2-pole switch and a wire sensor to measure and control the 

desired floor temperature. It can be either flush-mounted 

(standard) or surface-mounted (using special box).

The thermostat has a button for adjusting the temperature 

setting with a scale from 1 to 6 (each step corresponds to 

approximately 3°C). Furthermore, it has a LED indicator 

showing standby periods (green light) and heating periods 

(red light).

More information on this product can also be found at: 

devireg�devi�com

Table of Contents

Summary of Contents for DEVIreg Multi

















Reviews: