manualshive.com logo in svg

Danfoss AK-SM 850, User Manual, Page: 72 / 74

Share
Download
Danfoss AK-SM 850 User Manual Download Page 72

NOTES

Glossary of terms

RMT 

   Remote 

Management 

Tool

Viz  

 

 

 

Visual file.  Used in the RMT tool and sent  to the AK-SM for graphic Site View

System View 

 

 

Central page of AK-SM that displays all configured control points

Site View  

 

 

Custom graphic page with mapped system parameters

AK I/O:   

 

 

Danfoss AK Input / Output modules

Bd-Pt: 

 

 

 

Board & Point address location

Alarm Levels: 

 

 

Disabled = no alarm action

   

 

 

 

Log Only = logs alarm in database - no external action

   

 

 

 

Normal = Activate alarm output (once)

   

 

 

 

Severe = Activate alarm output (repeat based on severe repeat time)

   

 

 

 

Critical = Activate alarm output (repeat based on critical repeat time)

MAI 

   Master 

Application 

Image

CSI 

 

   Compressed 

Software 

Image

FAI 

 

   Factory 

Application 

Image

IP 

 

   Internet 

Protocol

EDF 

 

 

 

Extended Device File (a file that represents the physical device)

CAT (seen in EDF list) 

 

Category (1=Evap, 2=Pack, 8=HVAC, 16=Energy meter, 34=AKD102)

Relative schedule   

 

When set a relative schedule will offset against the operating hours (set under config/time)Host 

Communications   

 

The connection (via Ethernet) of one or more AK-SM units.  The connection between units is  

 

    known 

as 

‘host 

network’

Danfoss 

   http://danfoss.com

Veris 

Industries™ 

  http://www.veris.com/ 

Carlo Gavazzi™ 

  http://www.carlogavazzi.com/   

Continental Control Systems™ http://www.ccontrolsys.com/w/Home

 

72 

User Guide 

Lit. no. 

USCO.PI.R1.E1.02 © Danfoss 07-2013 

AK-SM 

850

Summary of Contents for AK-SM 850











































































Reviews:

No comments