DAN DRYER 3000 Maintenance And Service Manual Download

Page: 11 / 12

Reference

Version

Document

Lang.

Page

3000-ENG

08.01.2018

3000 DAN DRYER Hand dryer.

Maintenance and service manual

11 of 12

DAN DRYER A/S • Alsikevej 8 • DK-8920 Randers NV • www.dandryer.com • [email protected]

Warning !!!

During cleaning and service the hand dryer

must always be disconnected from the power

supply

Heating element replacement

1. Disconnect power supply.

2. Disassemble cover by removing the two cover

screws at the bottom of the housing. Use the

special Allen key which was originally supplied

with the hand dryer.

3. Disconnect wires from timer unit.

4. Disassemble sensor bracket and

timer unit from fan housing.

5. Loosen the two screws and dismount fan housing

from base plate.

9. Reassemble all components and test run

the hand dryer.

6. Loosen the screws and disassemble air outlet

from fan housing.

7. Disassemble heating element from air outlet.

8. Assemble new heating element and reassemble

all other components.

Summary of Contents for 3000













Search results

Summary of Contents for 3000

Reviews:

Related manuals for 3000

Brands by name

Popular brands

DAN DRYER 3000, Maintenance And Service Manual

Search results

Summary of Contents for 3000

Reviews:

Related manuals for 3000

Brands by name

Popular brands