background image

Reference

Version

Document

Lang.

Page

3000-ENG

08.01.2018

3000 DAN DRYER Hand dryer.

Maintenance and service manual

UK

2 of 12

DAN DRYER A/S • Alsikevej 8 • DK-8920  Randers NV • www.dandryer.com • [email protected]

Preface 

    2

General 

    2

Intended product use   

 

2

The supplier’s product liability   

2

Safety and warnings 

 

 

2

Installation and connection 

 

3

Adjustment of the machine 

 

4

Regular 

maintenance 

  5

Fault finding and solutions 

 

5

Cleaning the inside of the machine 

6

Spare 

parts 

   9

Carbon brush replacement 

 

10

Heating element replacement   

11

Technical specifications  

 

12

Dimensions 

   12

Wiring 

chart 

   12

Table of Contents:

Preface

Thank you for purchasing your equipment from

DAN DRYER A/S and congratulations on your

new hand dryer. If you use and maintain your

hand dryer according to our manual, it will work

to your satisfaction for many years.

General

The hand dryer must only be installed and

used in accordance with these instructions and

safety precautions. All service staff who work

with installation, servicing and repair of the

machine must have read and understood this

manual. If you have questions concerning the

use or maintenance of your machine, you are

welcome to contact us.

Intended product use

The hand dryer is designed for installation in

indoor public or private restrooms and may

only be used for hand drying.

The supplier’s product liability:

DAN DRYER A/S accepts no responsibility if

the machine is installed, used, modified or

composed otherwise than specified in this

manual.

Note !!!

The machine is designed for indoor use only.

Warning !!!

If the hand dryer is not installed and connected 

properly it can be dangerous to use due to the

risk of electric shock.

Always follow the installation instructions in this 

manual.

All service staff who work with servicing and

repairing of the machine must have read and

understood this manual.

Warning !!!

During cleaning, inspection, service etc. the hand 

dryer must always be disconnected from the

power supply.

All service staff who work with servicing and

repairing of the machine must have read and

understood this manual.

Safety Precautions:

Maintenance work requiring dismantling of the

machine must only be carried out by staff with 

proper training so the work can be carried out in

a secure manner.

Safety Precautions:

•  Check before use that:

•  the hand dryer is securely attached to the wall.

•  the hand dryer is properly cleaned.

•  the hand dryer is not damaged or otherwise in 

disorder.

Summary of Contents for 3000













Reviews: