Dalsa Linea ML ML-FM-08K30H Page 72 Manual Download

Page: 72 / 83

•

Camera Performance and Features

Display Name

Feature

Description

View

Current PRNU

Accesses the PRNU coefficients that are currently being used by
the camera (not necessarily saved).

CameraData

Download camera information and send for customer support.

File Operation
Selector

FileOperationSelector

Selects the operation for the selected file in the device. This
operation is executed when the File Operation Execute feature is
called.

1.00
Guru

Open

Select the Open operation - executed by FileOperationExecute.

Select the Close operation - executed by FileOperationExecute.

Read

Select the Read operation - executed by FileOperationExecute.

Write

Select the Write operation - executed by FileOperationExecute.

File Operation
Execute

FileOperationExecute

Executes the operation selected by File Operation Selector on
the selected file.

1.00
Guru

File Open Mode

FileOpenMode

Selects the access mode used to open a file on the device.

1.00
Guru

Read
Write

Select READ only open mode
Select WRITE only open mode

File Access
Buffer

FileAccessBuffer

Defines the intermediate access buffer that allows the exchange
of data between the device file storage and the application.

1.00
Guru

File Access
Offset

FileAccessOffset

Controls the mapping offset between the device file storage and
the file access buffer.

1.00
Guru

File Access
Length

FileAccessLength

Controls the mapping length between the device file storage and
the file access buffer.

1.00
Guru

File Operation
Status

FileOperationStatus

Displays the file operation execution status. (RO).

1.00
Guru

Success

The last file operation has completed successfully.

Invalid Parameter

InvalidParameter

An invalid parameter was passed to the last feature called.

Write Protect

WriteProtect

Attempt to write to a read-only (factory) file.

File Not Open

FileNotOpen

The file has not been opened yet.

File Too Big

FileTooBig

The file is larger than expected.

File Invalid

FileInvalid

The last file operation has completed unsuccessfully because
the selected file is not present in this camera.

File Operation
Result

FileOperationResult

For Read or Write operations, the number of successfully
read/written bytes is returned. (RO)

1.00
Guru

File Size

FileSize

Represents the size of the selected file in bytes.

1.00
Guru

Summary of Contents for Linea ML ML-FM-08K30H




















































































Search results

Summary of Contents for Linea ML ML-FM-08K30H

Reviews:

Related manuals for Linea ML ML-FM-08K30H

Brands by name

Popular brands

Dalsa Linea ML ML-FM-08K30H, Manual

Search results

Summary of Contents for Linea ML ML-FM-08K30H

Reviews:

Related manuals for Linea ML ML-FM-08K30H

Brands by name

Popular brands