Daktronics VANGUARD VL-3500 Series Display Manual Download

Page: 32 / 33

Glossary

RS422

: Standard differential communication type with a maximum cable length of 4,000'

(1.2 kilometers).

RX LED

: An LED on the signal converter that indicates the display is sending data back to

the signal converter.

Serial Port

: Connector on the back of the control computer. The serial port controls the

display network through either a 9- or 25-pin serial connector.

Signal Converter

: Component that converts data from RS232 to RS422 (wire converter) or

from RS232 to light signals (fiber converter). The signal converter is used in RS422 or fiber

systems.

Surge Suppressor

: A device inserted in the signal line and to prevent damage to

electronic equipment caused by voltage transients or spikes.

Translation Table

: Custom memory map for the display.

TX LED

: An LED on the signal converter that indicates the control computer is sending

data to the display.

Vanguard

Software

: Daktronics-designed, Windows®-based software that creates and

edits messages on displays.

Summary of Contents for VANGUARD VL-3500 Series


































Search results

Summary of Contents for VANGUARD VL-3500 Series

Reviews:

Related manuals for VANGUARD VL-3500 Series

Brands by name

Popular brands

Daktronics VANGUARD VL-3500 Series, Display Manual

Search results

Summary of Contents for VANGUARD VL-3500 Series

Reviews:

Related manuals for VANGUARD VL-3500 Series

Brands by name

Popular brands