manualshive.com logo in svg

Daktronics DVX-1200 Series, Installation & Service Manual, Page: 8 / 10

Share
Download
Daktronics DVX-1200 Series Installation & Service Manual Download Page 8

DVX-1200/2200/2210 Series Panel Installation & Service Quick Guide

Page 8 of 10

DD5166395
Rev 05
20 October 2023

201 Daktronics Drive

Brookings, SD 57006-5128

www.daktronics.com/support

800.325.8766

Cable

To remove a cable, follow these steps:

Note: 

Loosen cable gland nut to set the cable free.

 

Loosen fastener nut to remove the gland with cable.

1. 

Disconnect power to the display. 

2. 

Loosen the cable gland nut and fastener nut on the outside of the box. 

Refer to 

Figure 77

.

Figure 77: 

Loosen Cable Gland Nut and Fastener Nut

FASTENER NUT

CABLE GLAND NUT

3. 

Apply the cable gland removal tool to wrap the cable gland in the 

fitting angle, and push all the way to the bottom. Refer to

 Figure 78

. The 

cable can be pulled out for a distance when necessary by loosening 

the cable gland nut. 

Figure 78: 

Apply Cable Gland Removal Tool

4. 

Remove the connector of the power cable and signal cable from the 

hub board. Refer to 

Figure 68 

and

 Figure 69.

5. 

Use the removal tool to rotate the cable gland 90° so the notches are 

aligned with the box. Refer to 

Figure 79

. 

Figure 79: 

Rotate Cable Gland with Removal Tool

6. 

Remove 

cable gland removal tool

. Refer to 

Figure 80.

Figure 80: 

Remove Cable Gland Removal Tool

7. 

Cable gland is now loosened, pull the cable from below to 

remove the gland and cable out of the box. Refer to 

Figure 81

.

Figure 81: 

Remove Cable

Reverse these steps to install the cable.

Note: 

Properly re-install the cable and cable glands to make sure 

water does not get into the box.

Summary of Contents for DVX-1200 Series











Reviews:

No comments