Dakota Digital 3X Series Installation And Operation Manual Download Page 26 | Manualshive

Page: 26 / 36

background image

MAN 650067:G

26

BUS INTERFACE MODULE SETUP

The bus interface modules (BIM) can be added to Dakota Digital instrumentation

systems.  They allow you to add auxiliary gauge functions such as fuel pressure, vac/boost,
trans temp, etc., right into the system without having to add additional gauges.   All of the BIM
readings are displayed below the tachometer bar graph display in the message center.  Switch 2
(SW2) is used to cycle through the various message screens.

More detailed instructions are supplied with the BIM units.

INFORMATION MENU

The information menu “

INFO

” is used to display software code information should you

have any trouble this information can be useful for troubleshooting as well as the current
speedometer calibration value if using the normal speed input (SPD SND).

•

Press and hold SW1 while turning the key on.

•

Release the switch and then press and release SW1 to get to the “

INFO

” setup menu. You

should see “

SE5

x” on the speedometer display where x is the software number.

•

To view the current pulse per mile (PPM) setting, press and hold the SW1 until “

-

” “

INFO

”

•

is displayed.

•

Release the switch and the odometer will show the current PPM setting/calibration value.

•

Press and release the switch to go on to the next setup menu.

GEAR SETUP

The gear menu, “

GEAR

” is used to select how you want the system to display gear

position info. This information can only be displayed if an optional gear sending unit from
Dakota Digital, part number GSS-2000 is purchased, and wire the GEAR (1-WIRE) input or if
the Dakota Digital BIM-01-1 OBDII bus interface is purchased and connected with a compatible
transmission.

•

Press and hold SW1 while turning the key on.

•

Release the switch and then press and release SW1 to get to the “

GEAR

” setup menu.

•

Press and hold the switch until “

-

” “

GEAR

” is displayed to enter the setup menu, then release

SW1.

•

Press and release SW1 to scroll through the display options“

PRND21

”“

OVRDRV

” “

NONE

”.

o

Selecting “

PRND21

” the message center will display

PRND21

.

o

Selecting “

OVRDRV

” the message center will display

PRNOD21

.

o

Selecting “

NONE

” the message center will not display any gear information.

•

When the desired option is displayed; press and hold SW1 until you get “

-

” “

DONE

”.

•

Release the switch to go onto the next menu.

«
...
24
25
26
27
28
...
»

Summary of Contents for 3X Series





































Reviews:

No comments

Related manuals for 3X Series

IMAGEPRESS C7010VPS

Brand: Canon Pages: 4

Brand: DataSafe Pages: 4

Brand: Jeep Pages: 5

Brand: Jeep Pages: 6

Grand Cherokee SRT 2014

Brand: Jeep Pages: 345

Grand Cherokee 2015

Brand: Jeep Pages: 236

Brand: Jeep Pages: 18

Brand: Jeep Pages: 24

Brand: Jeep Pages: 560

Brand: Jeep Pages: 525

Brand: Jeep Pages: 308

Brand: Jeep Pages: 86

Brand: Jeep Pages: 638

Brand: Jeep Pages: 9

Brand: Jeep Pages: 51

Brand: Jeep Pages: 4

Brand: Jeep Pages: 50

Grand Cherokee SRT 2014

Brand: Jeep Pages: 118

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands