background image

7

English

(3)

If the piping length between the outdoor units exceeds 2 m, 
create a rise of 200 mm or more in the gas line under a length 
of 2 m from the outdoor unit multi connection piping kit.

5.

Branching the refrigerant piping
Heed the restrictions below when installing the refrigerant branch-
ing kit and read the installation instruction manual with the kit.
(Improper installation could lead to malfunctioning or breakdown 
of the outdoor unit.)

<REFNET joint>

Install the REFNET joint so it splits horizontally or vertically.

(Refer to figure 16)

1.

Horizontal surface

2.

±30° or less

3.

Horizontal

4.

Vertical

<REFNET header>

Install the REFNET header so it splits horizontally.

(Refer to figure 17)

1.

Horizontal surface

<Outdoor unit multi connection piping kit>

Install the joint horizontally so that the attached warning label 
faces strait up, and the tilt is within ±15°. 

(Refer to figure 18-1)

Do not install vertically. 

(Refer to figure 18-2)

Maintain a straight portion of 500 mm or more until the split of 
the joint without wrapping any onsite piping around this area. 
Over 500 mm of straight area can be maintained by connect-
ing at least 120 mm of onsite pipe (straight) to the joint.

(Refer to figure 18-3)

(Refer to figure 18)

1.

Warning label

2.

Horizontal surface

3.

±15° or less

4.

Ground

5.

Onsite pipe (120mm length or more)

6.

Straight part of 500mm or more

Prohibited pattern

Oil remains in the stopping outdoor unit.

Change to pattern 1 or pattern 2

Front connections

Side (bottom) connections

to indoor unit

to indoor unit

Oil remains in the outdoor unit B when the system stops.

Unit A

Unit B

Unit A

Unit B

Change as shown in the figure below.

Rising height:
200 mm or more

to indoor 
unit

to indoor 
unit

to indoor unit

to indoor unit

to indoor unit

to indoor unit

If less than 2m

If 2 m or more

2m or more

Rising height: 
200 mm or more

less than 2m

less than 2m

Outdoor unit gas pipe

Outdoor unit gas pipe

01_EN_3P226891-13Q.fm  Page 7  Thursday, December 2, 2010  10:15 AM

Summary of Contents for VRVIII-Q Series




























Reviews: