background image

6

English

6. OPERATION PROCEDURE

• Operation procedure varies according to the com-

bination of BS unit and remote controller. Read 
the chapter “What to do before operation”.

• To protect the unit, turn on the main power switch 

6 hours before operation.
And do not turn off the power supply during the air 
conditioning season because of smoothly start up.

• If the main power supply is turned off during oper-

ation, operation will restart automatically after the 
power turns back on again.

6-1

COOLING, HEATING, AUTOMATIC 
AND FAN ONLY OPERATION

• Automatic operation can be selected only on the 

heat recovery system.

• The operation mode cannot be changed with the 

remote controller whose display shows 

” (changeover under control).

Change the operation mode with the remote con-
troller whose display does not show “

”.

• When the display “

” (changeover under 

control) flashes, refer to the chapter “Operation 
procedure - Setting the master remote controller”.

• The fan may keep on running for about 1 minute 

after the heating operation stops for removing the 
heat in the indoor unit.

• The air flow rate may be ajusted automatically 

depending on the room temperature or the fan 
may stop immediately. This is not a malfunction.

• For machine protection the system may control 

the air flow rate automatically.

• It may take sometime for finishing to change the 

air flow rate.
This is normal operation.

FOR SYSTEMS WITHOUT COOL/HEAT SELEC-
TOR (Refer to figure 4)

Press the operation mode selector button sev-
eral times and select the operation mode of 
your choice;

” Cooling operation

” Heating operation

” Automatic operation

” Fan only operation

NOTE

• Automatic operation (Heat recovery system only)

In this operation mode, cool/heat changeover is 
automatically performed.

Press the on/off button.
The operation lamp lights up and the system 
starts operation.

FOR SYSTEMS WITH COOL/HEAT SELECTOR 
(Refer to figure 4 and 7)

Select operation mode with the Cool/Heat 
selector as follows:

” “

” Cooling operation 

(Refer to figure 7.1)

” “

” Heating operation 

(Refer to figure 7.2)

” 

 Fan only operation 

(Refer to figure 7.3)

Press the on/off button. 

(Refer to figure 4)

The operation lamp lights up and the system 
starts operation.

ADJUSTMENT (Refer to figure 4)

For adjustment the desired temperature, fan 
speed and air flow direction (only for FXC, FXF, 
FXH, FXK, FXA), follow the procedure shown 
below.

Press the temperature setting button and set 
the desired temperature.

Each time this button is pressed, the 
temperature setting rises or lowers 1°C.

NOTE

• Set the temperature within the operation 

range.

• The temperature setting is impossible for fan 

only operation.

Press the fan speed control button and select 
the fan speed of your preference.

Press air flow direction adjust button.
Refer to the chapter “Adjusting the air flow 
direction” for details.

STOPPING THE SYSTEM (Refer to figure 4)

Press the on/off button once again.
The operation lamp goes off and the system 
stops operation.

NOTE

• Do not turn off the power immediately after 

the unit stops.

• The system needs at least 5 minutes for 

residual operation of drain pump device.
Turning off the power immediately will cause 
water leak or trouble.

EXPLANATION OF HEATING OPERATION

• In heating operation, it may generally take longer 

to reach the set temperature than in cooling oper-
ation. 
We recommend starting the operation with timer.

Hot start operation

In order to prevent cold air from blowing out of an 
indoor unit at the start of heating operation, the 
indoor fan is automatically stopped. The display of 
the remote controller shows “

”.

1

2

1

2

3

4

5

6

01_EN_3P153897-7L.fm  Page 6  Friday, July 11, 2008  1:58 PM

Summary of Contents for VRV-WIII RWEYQ8PY1





















Reviews: