background image

English 2

 

Be sure to establish a ground.

 

Do not ground the unit to a utility pipe, arrester, or telephone 

ground. Incomplete grounding may cause electrical shock, or 

fire. A high surge current from lightning or other sources may 

cause damage to the air conditioner.

 

Although this is a recognized measure for additional protection, 

with the grounding system in North America, a dedicated GFCI 

may not be necessary.

CAUTION

 

Do not use the air conditioner or heat pump for any other 

purposes other than comfort cooling or heating. Do not use the 

unit for cooling precision instruments, food, plants, animals or 

works of art.

 

Do not place items under the indoor unit it could result in damage 

by condensates that may form if the humidity is above 80% or if 

the drain outlet gets blocked.

 

Before cleaning, stop the operation of the unit by turning the 

power off or by pulling the supply cord out from its receptacle. 

Otherwise, an electric shock and injury could result.

 

Do not wash the air conditioner or heat pump with excessive 

water. An electric shock or fire could result.

 

Avoid placing the controller in a spot splashed with water. Water 

entering the controller could result in an electric shock or 

damage the internal electronic parts.

 

Do not operate the air conditioner or heat pump when using a 

room fumigation type of insecticide. Failure to observe this 

could result in the chemicals to be deposited in the unit and can 

endanger the health of those who are hypersensitive to 

chemicals.

 

Do not turn off the power immediately after stopping operation. 

Always wait for at least five minutes before turning off the 

power. Otherwise, water leakage could result.

 

The appliance is not intended for use by young children or 

infirm persons without supervision.

 

The remote controller should be kept away from children so they 

cannot play with it.

 

Consult with the installation contractor for cleaning.

 

Incorrect cleaning of the inside of the air conditioner or heat 

pump could result in the plastics parts break resulting in water 

leakage or electric shock.

 

Do not touch the air inlet or aluminum fin of the air conditioner 

or heat pump as they can cut and could result in injury.

 

Do not place objects in direct proximity of the outdoor unit. Do 

not let leaves and other debris accumulate around the unit. 

Leaves are a hotbed for small animals which can enter the unit. 

Once inside the unit, animals result in the unit malfunctioning, 

and could result in smoke or fire when they make contact with 

electrical parts.

NOTE

 

Never press the button of the remote controller with a hard, 

pointed object. The remote controller result in damage.

 

Never pull or twist the electric wire of the remote controller. It 

may result in the unit malfunctioning.

 

Do not place appliances that produce open flames in places that 

are exposed to the air flow of the unit or under the indoor unit. It 

may result in incomplete combustion or deformation of the unit 

due to the heat.

 

Do not expose the controller to direct sunlight. The LCD display 

can become discolored and may result in fail to display the data.

 

Do not wipe the controller operation panel with benzene, thinner, 

chemical dust cloth, etc. The result may be that the panel 

becomes discolored or the coating can peel off. If it is heavily 

dirty, soak a cloth in water-diluted neutral detergent, squeeze it 

well and wipe the panel clean. Then wipe it with another dry 

cloth.

 

Dismantling of the unit, disposal of the refrigerant, oil, and 

additional parts, should be done in accordance with the relevant 

local, state, and national regulations.

 

Operate the air conditioner or heat pump in a sufficiently 

ventilated area and not surrounded by obstacles. Do not use the 

air conditioner or heat pump in the following places.

a. 

Places with a mist of mineral oil, such as cutting oil.

b.  Locations such as coastal areas where there is a lot of salt in 

the air.

c.  Locations such as hot springs where there is a lot of sulfur in 

the air.

d. 

Locations such as factories where the power voltage varies a 

lot.

e. 

In cars, boats, and other vehicles.

f. 

Locations such as kitchens where oil may splatter or where 

there is steam in the air.

g. 

Locations where equipment produces electromagnetic waves.

h. 

Places with an acid or alkaline mist.

i. 

Places where fallen leaves can accumulate or where weeds 

can grow.

 

Take snow protection measures. Contact your dealer for the 

details of snow protection measures, such as the use of a snow 

protection hood.

 

Do not attempt to do electrical work or grounding work unless 

you are licensed to do so. Consult with your dealer for electrical 

work and grounding work.

 

Pay Attention to Operating Sound. Be sure to use the following 

places:

a. 

Places that can sufficiently withstand the weight of the air 

conditioner or heat pump yet can suppress the operating 

sound and vibration.

b.  Places where warm air from the air outlet of the outdoor unit 

or the operating sound of the outdoor unit does not annoy 

neighbors.

 

Make sure that there are no obstacles close to the outdoor unit. 

Obstacles close to the outdoor unit may drop the performance 

of the outdoor unit or increase the operating sound of the 

outdoor unit.

 

Consult your dealer if the air conditioner or heat pump in 

operation generates unusual noise.

 

Make sure that the drainpipe is installed properly to drain water. 

If no water is discharged from the drainpipe while the air 

conditioner or heat pump is in the cooling mode, the result may 

be that the drainpipe becomes clogged with dust or dirt and 

water leakage from the indoor unit may occur. Stop operating 

the air conditioner or heat pump and contact your dealer.

[Place of Installation]

 

Make sure that the air conditioner is located in a sufficiently 

ventilated place not surrounded by obstacles.

 

Do not use the air conditioner in the following places.

a. 

Places with a mist of mineral oil, such as cutting oil.

b. 

Locations such as coastal areas where there is a lot of salt in the 

air.

c. 

Locations such as hot springs resorts where there is a lot of sulfur 

in the air.

d. 

Locations such as factories where the power voltage varies a lot.

e. 

In cars, boats, and other vehicles.

f. 

Locations such as kitchens where oil may splatter or there is 

steam in the air.

g. 

Locations where equipment that produces electromagnetic waves 

is found.

h. 

Places with an acid or alkaline mist.

i. 

Places where fallen leaves are accumulated or weeds grow close 

together.

 

Take snow protection measures.

 

Contact your local dealer for the details of snow protection measures, 

such as the use of a snow protection hood.

[Electrical Work]

 

Do not attempt to conduct electrical work or grounding work 

unless you are licensed to do so.

 

Consult with your local dealer for electrical work and grounding work.

 

Use a dedicated circuit for the air conditioner.

[Pay Attention to Operating Sound]

 

Be sure to use the following places.

a. 

Places that can sufficiently withstand the weight of the air 

conditioner and suppress the operating sound and vibration of the 

air conditioner.

b. 

Places where warm air from the air outlet of the outdoor unit or the 

operating sound of the outdoor unit does not annoy neighbors.

 

Make sure that there are no obstacles close to the outdoor unit.

 

Obstacles close to the outdoor unit may drop the performance of the 

outdoor unit or an increase in the operating sound of the outdoor unit.

 

Consult your local dealer if the air conditioner in operation 

generates unusual noise.

[Drainage through Drainpipe]

 

Make sure that the drainpipe is installed properly to drain water.

 

If no water is discharged from the drainpipe while the air conditioner 

is cooling operation, the drainpipe may be clogged with dust or dirt 

and water leakage from the indoor units may result. 

Stop operating the air conditioner and consult your local dealer.

Summary of Contents for VRV W T-series













































Reviews: