background image

4

English

2-4 COMBINATION

• This BS unit is only for systems for Models REYQ-P.

It cannot be connected to systems for Models REYQ-M.

• For series of applicable indoor units, refer to the catalog or other literature.
• Select the BS unit to fit the total capacity (sum of unit’s capacity) and max. number of the indoor units to be 

connected downstream. About indoor unit’s capacity, refer to the Table 2.

Table 1 

Table 2 

* About indoor unit’s capacity for HRV type (VKM), refer to the Engineering data book.

<

Example

>

In case of the BS unit witch connect two FXCQ32M and two FXSQ40M.

Total capacity = 31.25x2+40x2 = 142.5 

 Select BSVQ160P8V1B

2-5 CHECK ITEM

• For the following items, take special care during construction and check after installation is finished.

Completion check items

Hand-over check items

3. SELECTING INSTALLATION SITE

The equipment is not intended for use in a potentially explosive atmosphere.
Select an installation site where the following conditions are satisfied and that meets with your customer’s 
approval.

• Where is resistible against weight of BS unit.
• Locations where the wall is not significantly tilted.
• Where sufficient clearance for maintenance and service can be ensured. (Refer to Fig. 1)
• Locations where an inspection hole (Refer to Fig. 2) can be installed to EL. COMPO. BOX side (See Note).
• Where the total piping length involving indoor unit and outdoor unit is below the allowable piping length.

(See installation manual attached to outdoor unit.)

Model

Total capacity of all downstreem indoor units

Max. number of all downstreem indoor units

BSVQ100P8V1B

 100

5

BSVQ160P8V1B

100 < A 

 160

8

BSVQ250P8V1B

160 

<

 A 

 250

8

Capacity expressed as indoor unit’s model No.

20

25

32

40

50

63

80

100

125

200

250

Indoor unit’s capacity (for use in computation)

20

25

31.25

40

50

62.5

80

100

125

200

250

Check items

Problems

Check

Are the BS units installed securely?

Falling, vibration, and operating noise

Have you performed a gas leak test?

Does not cool or heat

Is the insulation complete? (Refrigerant piping and pipe connection part)

Water leaking

Is the voltage the same as that listed on the unit’s nameplate?

Does not operate/burnt out

Are all the wiring and piping correct?

Does not operate/burnt out

Is the unit grounded?

Dangers during electrical leak

Is the thickness of the power cord as specified?

Does not operate/burnt out

Check items

Check

Did you close the EL. COMPO. BOX lid?

Did you hand the operating manual and warranty card to the customer?

Summary of Contents for VRV III BSVQ100P8V1B





















Reviews: