background image

16

2. Press the FILTER SIGN RESET BUTTON of the

 

remote

controller after the air filter is cleaned and

 

attached.

The “

” (TIME TO CLEAN AIR FILTER) display turns

OFF.

Refer to the operation manual provided with the outdoor
unit for the positions of the “

” (TIME TO CLEAN AIR

FILTER) display and FILTER SIGN RESET BUTTON.

HOW TO CLEAN AIR OUTLET AND 

OUTSIDE PANELS (Field supply)

1.

Clean with soft cloth.

2.

When it is difficult to remove stains, use water or

neutral detergent.

NOTES

Do not use gasoline, benzene, thinner, polishing powder,

liquid insecticide. It may cause discoloring or warping.

shock or a fire.

result in discoloration or deformation.

For cleaning, consult with your Daikin dealer.(Before

each season when cooling or heating is required, clean

the air conditioner.)

If the area around the indoor unit is very dusty, use a

dust-proof cover (local procurement).

Cleaning the inside of the indoor unit

It is necessary to clean the inside of the indoor unit

periodically.

Since the cleaning requires special technologies,

request a Daikin dealer to clean them.

Daily maintenance:

Cleaning the air filter

Explanation

Removing the air filter except when cleaning the air

conditioner may result in accidents.

When the

 

mark is displayed on the remote

 

controller, please clean the filter.

When the operating time exceeds the desig-nated

time, this mark will be displayed.

If using the air conditioner under very dusty environment,

increase the frequency of air filter cleaning.

When you want to change the setting time until
the

 

mark is displayed, consult with your

 

dealer

.

(The default factory setting is 2500 hours.)

There are the following time, display pattern 1250,

2500, 5000, 10000.

Maintenace and Inspection

2. Clean it.

!

CAUTION

Do not wash the air conditioner with hot water of more than

50°C.  Doing so may result in discoloration or deformation.

Never dry the filter by direct firing.  Doing so may result in

burning.

For cleaning local procurements, consult with your dealer.

(

1) Use a vacuum cleaner (A) or wash the air filter (B) to

remove dust and trash.

(A) Remove dust and trash using a vacuum cleaner.

(B) Wash it with water.

When the air filter is very dirty, use a soft brush and

neutral detergent.

Dewater and dry in

 the shade.

3. Attach the air filter.
4. Push the “filter sign reset” button on the

 

remote

controller.

The display

 “ 

 ”

 vanishes.

1.

Method for servicing of Filter

Remove the 2 no. of Screw

2.

Remove Flange

3

.

Slide Filter for service/Cleaning.

1

.

3P

714597-2

DAIKIN AIRCONDITIONING INDIA PVT. LTD. 

Head office:-

12th Floor, Building No. 9, Tower A,

 

DLF Cyber City, 

DLF Phase-III,

 

Gurgaon-122 002, Haryana, 

(

India

DAIKIN Service Call Center

Toll free 1800-102-9300 (All Mobile/Landline)

1800-22-9300 (MTNL/BSNL)

Summary of Contents for VRV FXMQ100ARV16

















Reviews: