background image

13 Piping installation

Installation and operation manual

25

RXYSA4~6A7V/Y1B
VRV 5-S system air conditioner
4P600329-1A – 2020.01

INFORMATION

It  is  recommended  to  install  the  optional  bottom  plate
heater  (EKBPH250D7)  when  the  unit  is  installed  in  cold
climates.

12.3.4

To prevent the outdoor unit from falling
over

In  case  the  unit  is  installed  in  places  where  strong  wind  can  tilt  the
unit, take following measure:

1

Prepare  2  cables  as  indicated  in  the  following  illustration  (field
supply).

2

Place the 2 cables over the outdoor unit.

3

Insert  a  rubber  sheet  between  the  cables  and  the  outdoor  unit
to prevent the cables from scratching the paint (field supply).

4

Attach the ends of the cables.

5

Tighten the cables.

13

Piping installation

13.1

Preparing refrigerant piping

13.1.1

Refrigerant piping requirements

NOTICE

The  piping  and  other  pressure-containing  parts  shall  be
suitable  for  refrigerant.  Use  phosphoric  acid  deoxidised
seamless copper for refrigerant.

▪ Foreign materials inside pipes (including oils for fabrication) must

be ≤30 mg/10 m.

13.1.2

Refrigerant piping material

Piping material:

 Phosphoric acid deoxidised seamless copper.

Flare connections:

 Only use annealed material.

Piping temper grade and thickness:

Outer diameter

(Ø)

Temper grade

Thickness (t)

(a)

6.4 mm (1/4")

9.5 mm (3/8")

12.7 mm (1/2")

Annealed (O)

≥0.80 mm

t

Ø

15.9 mm (5/8")

Annealed (O)

≥0.99 mm

19.1 mm (3/4")

Half hard (1/2H)

≥0.80 mm

(a)

Depending on the applicable legislation and the maximum
working pressure of the unit (see "PS High" on the unit name
plate), larger piping thickness might be required.

13.1.3

To select the piping size

Determine  the  proper  size  using  the  following  tables  and  reference
figure (only for indication).

A

B-1

B-2

C-1

C-2

C-3

C-4

1

3-1

3-2

3-3

3-4

VRV DX

2

2

2

1

Outdoor unit

2

Refrigerant branch kits

3-1~3-4

VRV DX indoor units

A

Piping between outdoor unit and (first) refrigerant branch
kit

B-1 B-2

Piping between refrigerant branch kits

C-1~C-4

Piping between refrigerant branch kit and indoor unit

In  case  the  required  pipe  sizes  (inch  sizes)  are  not  available,  it  is
also allowed to use other diameters (mm sizes), taken the following
into account:

▪ Select the pipe size nearest to the required size.

▪ Use  the  suitable  adapters  for  the  change-over  from  inch  to  mm

pipes (field supply).

▪ The  additional  refrigerant  calculation  has  to  be  adjusted  as

mentioned  in 

"14.2  To  determine  the  additional  refrigerant

amount" 

[

4

 29].

A: Piping between outdoor unit and (first)
refrigerant branch kit

When  the  equivalent  pipe  length  between  outdoor  unit  and  the
furthest indoor unit is 90 m or more (b+d), the size of the main gas
pipe  (b)  must  be  increased  (size-up).  If  the  recommended  gas  pipe
(size-up)  is  not  available,  you  must  use  the  standard  size  (which
might result in a small capacity decrease).

e

d

b

c

a

a

Outdoor unit

b

Main gas pipe (increase piping size if length b+d ≥ 90 m)

c

First refrigerant branch kit

d

Piping between indoor unit and first refrigerant branch kit

e

Furthest indoor unit

Outdoor unit

capacity type (HP)

Piping outer diameter size (mm)

Gas pipe

Liquid pipe

Standard

Size-up
(only b)

4+5+6

15.9

19.1

9.5

B: Piping between refrigerant branch kits

Choose  from  the  following  table  in  accordance  with  the  indoor  unit
total  capacity  type,  connected  downstream.  Do  not  let  the
connection  piping  exceed  the  refrigerant  piping  size  chosen  by  the
general system model name.

Summary of Contents for VRV 5-S Series

















































Reviews: