background image

 

T-CU19-JAN24-1 

 

 

Page 18 

Inverter compressor start-up: 

 

Compressor is managed to start-up by adapting operating 
speed to guarantee that the desired conditions and 
excellent lubrication are reached very quickly. For this 
reason, when starting the compressor is operated at a 
settable fixed speed (Cag52) for the minimum ON time. 
During this stage, the out-of-envelope alarm is disabled, 
but speed control remains active if approaching or 
exceeding zone 2 (maximum compression ratio), 3 
(maximum condensing pressure) or 4 (current limit). 
                  
If 45 seconds after compressor start-up, the pressure 
differential is less than 0.2barg higher than the value 
measured at start-up, the controller stops the compressor 

and generates a “No compressor start

-

up” alarm. This 

alarm is automatically reset, and the controller tries to start 
the compressor five times after a 30 second delay. After 
the fifth attempt, the alarm is no longer automatically reset. 
 

Figure 12: Compressor Startup Curve  

 

 
The corresponding parameters are in loop: Compressors -> 
Advanced -> masks Cag50, Cag51, Cag52: 
 

  

 
   

 

Pressure differential during 

start-up 

 

 

The BLDC compressor 

cannot start if the pressure 

differential is greater than 9.0barg

. This limit depends 

on the maximum current delivered by the inverter. As 
soon as the pressure differential falls below the 
minimum threshold, the compressor can start. 

 

The corresponding parameters are in loop: 
Compressors -> Advanced -> mask Cag49: 

 

When the pressure differential is 8.5barg (fixed 
value), the compressor is ready to start. 
 

 

 
Minimum pressure differential for lubrication 

 
The min. pressure differential threshold for correct 
lubrication is related to the type of BLDC compressor and 
cannot be modified. The low-pressure differential alarm is 
generated when the difference between condensing 
pressure and evaporation pressure (DeltaP) remains below 
the limit defaulted for a set time, and consequently 
excellent lubrication is not guaranteed. The alarm stops the 
compressor and is reset automatically. The alarm is not 
active during defrosting. 
 
The corresponding parameters are in loop: Compressors -> 
Advanced-> mask Cag55: 

 
 
 
 
 
 

 

 
 

Times 

 

Time management includes a minimum On time, a minimum 
Off time and a minimum time between two consecutive 
starts. These parameters can be modified under 
Compressors -> Configuration -> mask Caf35:  
 

 

 

Figure 13: Times Control for Compressor Startup 

 

 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for V3



































Reviews: