background image

 

T-CU19-JAN24-1 

 

 

Page 16 

Changing Set Point 

 

1. With controller Home screen displayed, Press PRG button 

to go Main Menu screen and select “A. Unit Status”, press 
ENTER and select “b. Setpoint” by DOWN button. Screen 

Ab01 is displayed. To adjust the setpoint, you need the 
cursor to be by the User setp., then use UP/DOWN buttons 
to adjust value and then press ENTER to confirm setting.  
 

 

2. 

Return the cursor to its ‘home starting point’ before you 

can move to the next screen Ab05 by pressing the DOWN 
button. Press ENTER until cursor point to User setp., use 
UP/DOWN button to adjust value. Press ENTER to confirm 
the setting and then ESC button repeatedly to return to 
Home screen.  
Please note that the set point value of 16.0 bar is 
recommended for R448A/R449A/R404A operation. 
 
 

Refrigerant Selection  

*Applicable only with manufacturer password  
 

All below steps must be accomplished if 
refrigerant is changed from default: 
 

1.

 

Press PRG to go to the main 

menu, select “C. 

Compressor” and press ENTER. Select “g. Advanced” 

and press ENTER. Enter screen Cag01: Refrigerant 
Type. Press ENTER to move cursor and UP/DOWN 
button to select type of refrigerant. Press ENTER for 
execution and press DOWN button to move to the next 
screen.  

 
 
 
 
 
 
 

2.

 

Cag02: Select the compressor model. Refer compressor 
nameplate on the unit to ensure correct model is 
selected. Change Set Default: YES. Press ENTER for 

execution. Press ESC button to go back to “g. 
Advanced”. Press ENTER and DOWN button to go to 

mask Cag49.  

3.

 

Cag49: Change Max pressure differ. admitted: 
9.0bar. Press ENTER for execution.  

 
 
 
 
 
 
 

4.  Cag52:  Start-up  forced  speed:  60.0rps;  Max  speed: 
100.0rps; Min speed: 30.0rps. Press ENTER for the execution. 

 

 

 

 

Ensure all data on Cag02, Cag49 and Cag52 
are changed accordingly if Cag01 is modified 
on the type of refrigerant.  

 

Switch Unit ON/OFF (By 
Controller) 

*Applicable only with service password and manufacturer 
password 

 
1.

 

With controller Home screen displayed, Press PRG 

button to go Main Menu screen and select “A. 

Unit 

Status

.  

2.

 

Press ENTER button. Screen “Unit Status” is displayed. 
Select “c. On/Off” and then press ENTER button. 

 

3.

 

Switch Unit ON by using ENTER button. Indicator 
pointing to ON means Unit is ON. (Press ENTER button 
if want switch to OFF position.  

4.

 

Press ESC button repeatedly to return to Home Screen. 
This should now show ON by KEY at the bottom of the 
screen.  

5.

 

The unit will start up following a short delay (assuming 
all conditions for compressor start-up are met).  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for V3



































Reviews: