Daikin Trailblazer AGZ030E-070E Installation, Operation And Maintenance Manual Download Page 36

Page: 36 / 148

IOM 1207-6 • TRAILBLAZER

MODEL AGZ CHILLERS

36 www.DaikinApplied.com

Dimensions and Weights - Remote Evaporator Units

Figure 38: Remote Evap Condensing Unit - 8 Fan; AGZ110E-AGZ130E

37 1.5

609 24.0

4879 192.1

996 39.2

229 9.0

167 6.6

486 19.1

51 2.0

80 3.1

305 12.0

127 5.0

22 .875

KNOCKOUTS

POWER ENTRY KNOCKOUTS ARE ONTHE OPPOSITE SIDE OF THE CONTROL BOX

L1 L2

L3 L4

L1 - L4, LIFTING

LOCATIONS

LIQUID

HOT GAS

SUCTION

2506 98.6

2355 92.7

213 8.4

2235 88.0

DIMENSION DOES NOT INCLUDE

LIFTING BRACKETS

165 6.5

175 6.9

292 11.5

64 2.5

22 .875

KNOCKOUTS

FIELD CONTROL CONNECTIONS

QTY. 3

CONTROL

BOX

[22]

.875 POWER ENTRY

KNOCKOUTS FRONT OR RIGHT SIDE

315 12.4

2433 95.8

1499 59.0

630 24.8

52 2.0

19 .750

QTY. 6

52 2.0

826 32.5

190 7.5

204 8.0

189 7.4

2598 102.3

TYP.

M1 - M6, ISOLATOR MOUNTING HOLE LOCATIONS ON BOTTOM SURFACE OF

UNIT BASE.

COMPR. CIR. 2

COMPR. CIR. 1

TOP VIEW WITH COILS AND FANS REMOVED.

SUCTION CIR. 1

SUCTION CIR. 2

LIQUID & HOT GAS CIR. 2

LIQUID & HOT GAS CIR. 1

NOTE: LIFTING WEIGHTS ARE BASED ON UNIT SHIPPING WEIGHTS.

MOUNTING WEIGHTS ARE BASED ON UNIT OPERATING WEIGHT

WITH REFRIGERANT

INCLUDED.

SHIPPING AND OPERATING WEIGHTS DO NOT INCLUDE THE WEIGHTS OF AN

OPTIONS OR ACCESSORIES.

NOTE:

IT IS RECOMMENDED THAT THE SIDE LOCATIONS BE USED
1.

FOR POWER ENTRY WIRE SIZES LARGER THAN 350 MCM.

334547125

UNIT

LOCATION

MODEL

IN.

AGZ110E

44.4

1128

43.9

1115

66.3

1684

AGZ120E

44.3

1125

42.2

1072

65.2

1656

44.2

1123

42.1

1069

65.8

1671

UNIT

REFRIGERANT

CONNECTIONS

MODEL

SUCT.

O.D.

LIQ

. O.D.

IN.

AGZ110E AGZ120E

2.63

66.8

1.13

28.7

AGZ130E

HGBPO.D. IN.

1.13

28.7

SHIP

WEIGH

PER.

WEIGHl

LIFTING

(SHIPPING)

WEIGH

CORNER

UNIT

MODEL

LBS

AGZ110E

4894

222

5150

233

1631

740

1657

752

797

362

810

367

1369

621

1391

AGZ120E

5097

2312

5357

2430

1721

781

1748

793

808

367

820

372

1446

656

1468

AGZ1

5123

2324

5383

1723

782

1738

788

827

834

378

1446

656

1458

MOUNT

ING

(OPERATING)

IGHT

LBS

788

357

410

186

416

189

666

804

365

816

370

408

185

415

188

661

812

368

819

371

422

191

426

193

Summary of Contents for Trailblazer AGZ030E-070E





















































































































































Search results

Summary of Contents for Trailblazer AGZ030E-070E

Reviews:

Brands by name

Popular brands

Daikin Trailblazer AGZ030E-070E, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Trailblazer AGZ030E-070E

Reviews:

Brands by name

Popular brands