manualshive.com logo in svg

Daikin Trailblazer AGZ030E-070E, Installation, Operation And Maintenance Manual

Share
Download
Daikin Trailblazer AGZ030E-070E Installation, Operation And Maintenance Manual Download Page 106

IOM 1207-6 • TRAILBLAZER

®

 MODEL AGZ CHILLERS 

106 www.DaikinApplied.com

Using the Controller

Using the Controller

Compressor Communications

The CoreSense™ compressor communication module 

on model sizes 075-241 provides advanced diagnostics, 

protection, and communications that enhance compressor 

performance and reliability. 
Features include motor temperature protection, scroll 

temperature protection, missing phase protection, reverse 

phase protection, low control circuit voltage protection, short 

cycling detection and alert, operational and fault history 

storage, and LED status display. 

Warnings and Alerts

A solid green LED indicates the module is powered and 

operation is normal. 
A solid red LED indicates an internal problem with the module.

A flashing green LED communicates Warning codes. Warning 

codes do not result in a trip or lockout condition.

A flashing red LED communicates Alert codes. Alert codes will 

result in a trip condition and possibly a lockout condition

Warning Codes (Flashing Green LED )

Code 1

 – Loss of Communication: The module will flash the 

green Warning LED one time indicating the module has not 

communicated with the master controller for longer than 5 

minutes.

Code 2

 – Reserved For Future Use

Code 3

 – Short Cycling: The module will flash the green 

Warning LED three times indicating the compressor has short 

cycled more than 48 times in 24 hours. 

Code 4

 – Open/Shorted Scroll Thermistor: The module will 

flash the green Warning LED four times indicating an open/

shorted 

Alert/Lockout Codes (Flashing Red LED)

Code 1

 – Motor High Temperature: The module will flash the 

red Alert LED one time indicating the motor is overheating . 

A code 1 Alert will open the M2-M1 contacts. The Alert will 

reset after 30 minutes. Five consecutive Code 1 Alerts will 

lockout the compressor. Once the module has locked out the 

compressor, a power cycle or Modbus reset command will be 

required for the lockout to be cleared.

Code 2

 – Open/Shorted Motor Thermistor: The module will 

flash the red Alert LED two times indicating the motor PTC 

thermistor circuit has an open/shorted thermistor chain (see 

Table 2). A Code 2 Alert will open the M2-M1 contacts. The 

Alert will reset after 30 minutes and the M2-M1 contacts will 

close if the resistance of the motor PTC circuit is back in the 

normal range. The module will lockout the compressor and a 

power cycle or Modbus reset command will be required to clear 

the lockout.

Code 3 

– Short Cycling: The module will flash the red Alert 

LED three times indicating the compressor is locked out due to 

short cycling. Once locked out the compressor, a power cycle 

or Modbus reset command will be required to clear the lockout.

Code 4

 – Scroll High Temperature: The module will flash 

the red Alert LED four times indicating the over-temperature 

condition. A Code 4 Alert will open the M2-M1 contacts.The 

Alert will reset after 30 minutes. Once the module has locked 

out the compressor, a power cycle or Modbus reset command 

will be required to clear the lockout.

Code 5

 – Reserved for Future Use

Code 6

 – Missing Phase: The module will flash the red Alert 

LED six times indicating a missing phase. The Alert will reset 

after 5 minutes and the module will lockout the compressor 

after 10 consecutive Code 6 Alerts. Once locked out, a power 

cycle or Modbus reset is required.

Code 7

 – Reverse Phase: The module will flash the red Alert 

LED seven times indicating a reverse phase in two of the three 

compressor leads.  The modules will lockout the compressor 

after one Code 7 Alert. A power cycle or Modbus reset 

command will be required to clear the lockout.

Code 8

 – Reserved For Future Use

Code 9

 – Module Low Voltage: The module will flash the red 

Alert LED nine times indicating low module voltage for more 

than 5 seconds. The Alert will reset after 5 minutes and the M2-

M1 contacts will close if the T2-T1 voltage is above the reset 

value.

NOTE: 

If a compressor with CoreSense Communications 

fails in the field, the CoreSense module should 

remain with the failed compressor so the 

manufacturer’s technicians can download the 

CoreSense data to assist with determining the root 

cause of compressor failure.

Summary of Contents for Trailblazer AGZ030E-070E





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands