manualshive.com logo in svg

Daikin Trailblazer AGZ030E-070E, Installation, Operation And Maintenance Manual

Share
Download
Daikin Trailblazer AGZ030E-070E Installation, Operation And Maintenance Manual Download Page 140

IOM 1207-6 • TRAILBLAZER

®

 MODEL AGZ CHILLERS 

140 www.DaikinApplied.com

Warranty Registration Form (Scroll)

REFRIGERANT PIPING FOR  REMOTE EVAPORATOR APPLICATIONS

A. Has all field piping been leak tested at 150 psig (690 kPA)?

B. Has system been properly evacuated and charged?

C. Refrigerant R-

Circuit 1

lbs (kg) Circuit 2

lbs. (kg)

D.

Reviewed and confirmed piping is per the approved SF-99006 form submitted to the factory?

E. Is a liquid line filter-drier installed in each circuit?

F. Is a liquid line solenoid installed correctly in each circuit?

G. Is Expansion Valve and associated sensors installed, insulated and wired correctly?

(Including Entering water and Leaving water sensors.)

DESIGN CONTROLS

Ft. (kPa) 

Leaving

°F (°C)

A.

CHILLER

Water Pressure Drop:

Water Temperatures:  Entering

B.

CONDENSER

Design Ambient Temperatures

:

 Entering

Minimum Ambient Temperatures

: Entering

°F (°C)

°F (°C)

gpm (lps)

 

°F (°C)

°F (°C)

START-UP

A.

Does unit start and perform per sequence of operation as stated in the 

IOM

 Manual?

B.

Do condenser fans rotate in the proper directions?

MICROTECH STATUS CHECK-Each Reading Must be Verified with Field Provided Instruments of Known Accuracy?

MicroTech

Verification

C. Water Temperatures:    Leaving Evaporator

………………………………

°F (°C)

°F (°C)

Entering Evaporator

………………………………

°F (°C)

°F (°C)

D. Circuit #1 Refrigerant Pressures:

Evaporator ………………………………………….

psig (kPa)

psig (kPa)

Liquid Line pressure

……………………………………………………………..

psig (kPa)

Condenser Pressure

………………………………

psig (kPa)

psig (kPa)

E. Circuit #2 Refrigerant Pressures:

Evaporator ………………………………………….

psig (kPa)

psig (kPa)

Liquid Line Pressure

…………………………………………………………….

psig (kPa)

Condenser Pressure

……………………………..

psig (kPa)

psig (kPa)

F. Circuit #1 Refrigerant Temperatures:

Saturated Evaporator Temperature ……………………

°F (°C)

°F (°C)

Suction Line Temperature ……………………………….

°F (°C)

°F (°C)

Suction Superheat ……………………………………….

°F (°C)

°F (°C)

Saturated Condenser Temperature ……………………

°F (°C)

Liquid Line Temperature …………………………………………………………..

°F (°C)

Subcooling …………………………………………………………………………..

°F (°C)

Discharge Temperature

…………………………………………………………..

°F (°C)

SF-

20001

 AGZ/AMZ Start-Up 

8

/2020

3

 of 

8

www.DaikinApplied.com

N/A   Yes    No

Yes   No

°F (°C)

Leaving
Leaving

psig(kPa)

Summary of Contents for Trailblazer AGZ030E-070E





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands