background image

18

English

Observe the notes mentioned below when wiring to the terminals.

Tightening torque for the terminal screws.

Use the correct screwdriver for tightening the terminal screws. If the blade of screwdriver is too small, the 
head of the screw might be damaged, and the screw will not be properly tightened.

If the terminal screws are tightened too hard, screws might be damaged.

Refer to the table below for the tightening torque of the terminal screws.

Precautions to be taken for power supply wiring

Use a round crimp-style terminal for connection to the power supply terminal block. 
In case it cannot be used due to unavoidable reasons, be sure to observe the following instructions. 

(Refer to Fig. 30)

Do not connect wires of different gauge to the same power supply terminal. (Looseness in the connection 
may cause overheating.) 

(Refer to Fig. 31)

When connecting wires of the same gauge, connect them according to. 

(Refer to Fig. 31)

In wiring, make certain that prescribed wires are used, carry out complete connections, and fix the wires so 
that external forces are not applied to the terminals.

Terminal

Size

Tightening torque

Remote controller terminal block (2P)

M3.5

0.79 - 0.97 N•m

Power supply terminal block (3P)

M4

1.18 - 1.44 N•m

Ground terminal

M4

1.18 - 1.44 N•m

Electric wire

Round crimp-style terminal

Attach insulation sleeve

Fig. 30

Good

Wrong

Wrong

Connect wires of the 
same gauge to both 
side. (GOOD)

Do not connect wires 
of the same gauge to 
one side. (WRONG)

Do not connect wires 
of different gauges. 
(WRONG)

Fig. 31

01_EN_3PN06588-4M.fm  Page 18  Monday, December 19, 2011  7:04 PM

Summary of Contents for Super Multi NX FHQ35BVV1B































Reviews: