background image

RZQG71~140L + RZQSG100~Y1B(9)

Split system air conditioners

4P327537-1 – 2012.08

Installation manual

6

6.2.

Installation method for prevention of falling over

If it is necessary to prevent the unit from falling over, install as shown 
in the figure.

prepare all 4 wires as indicated in the drawing

unscrew the top plate at the 4 locations indicated A and B

put the screws through the nooses and screw them back tight

A

Location of the 2 fixation holes on the front side of the unit

B

Location of the 2 fixation holes on the rear side of the unit

C

Wires: field supply

6.3.

Drain pipe disposal

Make sure the drain works properly.

In regions where buildups of snow can be expected, the 
accumulation and freezing of snow in the space between the 
heat exchanger and external plate may lower operating 
efficiency. In this case, drill a knock-out hole in the lower part of 
the bottom frame so the snow can escape. When creating a 
knock-out hole, use a Ø6 mm drill bit to open round holes 
connected to the circumference of the knock-out hole (4 places).

After punching the knock-out hole, the application of repair-type 
paint on the surface around the edge sections is recommended 
to prevent rust.

7.

Installation service space

The installation service spaces shown in the illustrations are 
based on an air intake temperature of 35°C (DB) for COOL 
operation. In regions where the air intake temperature regularly 
exceeds 35°C (DB), or if the heat load of outdoor units is 
expected to regularly exceed the maximum operating capacity, 
reserve a larger space than that indicated at the air intake side 
of units.

Regarding the required air outlet space, position the units with 
consideration to the space required for the onsite refrigerant 
piping work as well. Consult your dealer if the work conditions do 
not match those in the drawings.

7.1.

Precaution on installation

(A) In case of non-stacked installatio

(See figure 1)

 (Unit : mm)

(A-1)

 Single unit installation

(A-2)

 Multiple units installation (2 units or more)

- Secure appropriate space when using a side piping outlet.

(B) In case of stacked installation

1.

In case obstacles exist in front of the outlet side.

2.

In case obstacles exist in front of the air inlet.

Do not exceed two levels for stacked installation.

Install a roof cover as shown in the figures above (field supply), 
as outdoor units with downward drainage are subject to dripping 
and freezing of that drain water.

Install the upper outdoor unit so that its bottom plate is at 
sufficient height above the roof cover. This is to prevent the 
buildup of ice on the bottom plate outer surface. A space of at 
least 500 mm is recommended.

It is not necessary to install a roof cover if there is no danger of 
drainage dripping and freezing. In this case, the space between 
the upper and lower outdoor units should be at least 100 mm. 
Close the gap between the upper and lower units so there is no 
re-intake of discharged air.

(C) In case of multiple-row installation (for roof top use, etc.)

1.

In case of installing one unit per row.

A

C

B

1

2

3

1

Drill

2

Area around knock-
out hole

3

Knock-out hole

Suction side obstacle

Obstacle is present

Discharge side obstacle

1

In these cases, close the 

bottom of the installation 

frame to prevent the 

discharged air from being 

bypassed

Left side obstacle

Right side obstacle

2

In these cases, only 2 units 

can be installed.

Top side obstacle

This situation is not allowed

A

•

•

A

Roof cover (field supply)

A

•

•

A

Roof cover (field supply)

•

•

•

•

Summary of Contents for SkyAir RZQG71L7V1B

























Reviews: