background image

3

CAUTION

While following the instructions in this installation manual, 
install drain piping in order to ensure proper drainage and insu-
late piping in order to prevent condensation.

Improper drain piping may result in water leakage and property dam-
age.

Be very careful about product transportation.

Do not touch the refrigerant pipes during and immediately after 
operation.

During and immediately after operation, the refrigerant pipes may be 
hot and may be cold, depending on the condition of the refrigerant 
flowing through the refrigerant piping, compressor, and other refrig-
erant cycle parts. Your hands may suffer burns or frostbite if you 
touch the refrigerant pipes.

Do not turn off the power immediately after stopping operation. 

Always wait at least five minutes before turning off the power. Other-
wise, water leakage and trouble may occur.

Do not use a charging cylinder.

Using a charging cylinder may cause the refrigerant to deteriorate.

The refrigerant R410A requires strict cautions for keeping the 
system clean, dry and tight.

A.Clean and dry

Foreign materials (including mineral oils such as SUNISO oil or
moisture) should be prevented from getting mixed into the system.

B.Tight

R410A does not contain any chlorine, does not destroy the ozone
layer, and does not reduce the earth’s protection against harmful
ultraviolet radiation.
R410A can contribute slightly to the greenhouse effect if it is released.
Therefore we should take special attention to check the tightness of
the installation.
Read the chapter “Refrigerant piping work” carefully and follow
these procedures correctly.

Since R410A is a mixed refrigerant, the required additional 
refrigerant must be charged in its liquid state. (If the refrigerant 
is charged in a state of gas, its composition changes and the 
system will not work properly.)

The indoor unit is for R410A. See the catalog for indoor unit models
which can be connected.
(Normal operation is not possible when connected to other units.)

For installation of the indoor units, refer to the installation man-
ual supplied together with each indoor unit.

Never operate the air conditioner with the discharge pipe ther-
mister (R3T), suction pipe thermister (R2T) and pressure sen-
sors (S1NPH, S1NPL) removed. 

 

Such operation may burn out the compressor.

Make sure to provide for adequate measures in order to prevent 
that the outdoor unit be used as a shelter by small animals.

Small animals making contact with electrical parts can cause mal-
functions, smoke or fire. Please instruct the customer to keep the 
area around the unit clean.

NOTE

Install the indoor and outdoor units, power supply wiring and 
transmission wiring at least 3.5ft. away from televisions or 
radios in order to prevent image interference or noise.

(Depending on the radio waves, a distance of 3.5ft. may not be 
enough to eliminate the noise.)

Dismantling of the unit, treatment of the refrigerant, oil and 
eventual other parts, should be done in accordance with the rel-
evant local and national regulations.

Do not use the following tools that are used with conventional 
refrigerants. (Gauge manifold, charge hose, gas leak detector, 
reverse flow check valve, refrigerant charge base, vacuum 
gauge, refrigerant recovery equipment.)

If the conventional refrigerant and refrigerator oil are mixed in the 
R410A, the refrigerant may deteriorated.

Never perform outdoor unit piping connection work when it is 
raining.

〈〈〈〈

Safety Precaution

〉〉〉〉

The PCI Data Station is a class A product. In a domestic environment 
this product may cause radio interference in which case the user may 
be required to take adequate measures.

2. INTRODUCTION

2-1 Standard operation limit

The figures below assume following operating conditions for indoor and 

outdoor units:

Equivalent pipe length...................... 25 ft.

Level difference................................ 0 ft.

A

Outdoor temperature (°FDB)

B

Indoor temperature (°FWB)

C

Outdoor temperature (°FWB)

D

Indoor temperature (°FDB)
Range for continuous operation
Range for pull down operation
Range for warming up operation
Range for operation

2-2 Technical specifications

(

<a> and 

<b>  in the table indicate the operating condition (shown in 

the figure bottom left).)

2-3 Electrical specifications

(

<c> in the table indicate the operating condition (shown in the 

figure bottom left).)

Model

RZQ24MVJU RZQ30MVJU RZQ36MVJU RZQ42MVJU

Precaution

Refrigerant

R410A

Power

208-230V 60Hz 

Cooling capacity

(MBh)

24

30

36

42

<a>

Heating capacity

(MBh)

27

33

38

45

<b>

Dimensions

(inch)

52 15/16 × 35 7/16 × 12 5/8

H × W × D
Weight

(lb.)

310

Connections

Gas

(inch)

5/8

Liquid

(inch)

3/8

Model

RZQ24MVJU RZQ30MVJU RZQ36MVJU RZQ42MVJU

Precaution

Power

Phase

~

Frequency

(Hz)

60

Voltage

(V)

208-230

Voltage 
torerance

(%)

±10

Rated current
 of fuse

(A)

30

Compressor

Phase

3~

Frequency

(Hz)

60

Voltage

(V)

208-230

Min. Circuit Amps.

(A)

27.0

<c>

Cooling

Heating

<b>

B

<c>

A

C

D

<a>

– 4

5

59

115

41

50

50

43

70

95

81

50

23

77

60

67

82

57

01_EN_3PN05597-5R.fm  Page 3  Wednesday, September 14, 2005  8:35 PM

Summary of Contents for RZQ24MVJU


















Reviews: