background image

7 Commissioning

Installation and operation manual

20

RXYSQ6T7Y1B9

VRV IV-S system air conditioner

4P397285-1B – 2016.03

Setting

 (= binary)

Value

Description

[2‑30] 

Power consumption limitation level (step 1) via the external control
adaptor (DTA104A61/62).

If the system needs to be running under power consumption
limitation conditions when an external signal is sent to the unit, this
setting defines the level power consumption limitation that will be
applied for step 1. The level is according to the table.

60%

(default)

70%

80%

[2‑31] 

Power consumption limitation level (step 2) via the external control
adaptor (DTA104A61/62).

If the system needs to be running under power consumption
limitation conditions when an external signal is sent to the unit, this
setting defines the level power consumption limitation that will be
applied for step 2. The level is according to the table.

30%

(default)

40%

50%

[2‑32] 

Forced, all time, power consumption limitation operation (no
external control adaptor is required to perform power consumption
limitation).

If the system always needs to be running under power
consumption limitation conditions, this setting activates and defines
the level power consumption limitation that will be applied
continuously. The level is according to the table.

(default)

Function not active.

Follows [2‑30] setting.

Follows [2‑31] setting.

[2‑41] 

Cooling comfort setting.

This setting is used in conjunction with setting [2‑8].

Eco

(default)

Mild

Quick

Powerful

[2‑42] 

Heating comfort setting.

This setting is used in conjunction with setting [2‑9].

Eco

(default)

Mild

Quick

Powerful

6.1.9

To connect the PC configurator to the
outdoor unit

a

b

X41A

A1P

2

3

4

5

H J

ST

a

PC

b

Cable (EKPCCAB)

X41A

Connector

A1P

Outdoor unit main PCB

7

Commissioning

After installation and once the field settings are defined, the installer
is  obliged  to  verify  correct  operation.  Therefore  a  test  run  must  be
performed according to the procedures described below.

7.1

Precautions when commissioning

CAUTION

Do not perform the test operation while working on the
indoor units.

When  performing  the  test  operation,  not  only  the  outdoor
unit,  but  the  connected  indoor  unit  will  operate  as  well.
Working on an indoor unit while performing a test operation
is dangerous.

NOTICE

Be  sure  to  turn  on  the  power  6  hours  before  operation  in
order  to  have  power  running  to  the  crankcase  heater  and
to protect the compressor.

During test operation, the outdoor unit and the indoor units will start
up.  Make  sure  that  the  preparations  of  all  indoor  units  are  finished
(field  piping,  electrical  wiring,  air  purge,  ...).  See  installation  manual
of the indoor units for details.

7.2

Checklist before commissioning

After the installation of the unit, first check the following items. Once
all below checks are fulfilled, the unit must be closed, only then can
the unit be powered up.

You  read  the  complete  installation  and  operation
instructions,  as  described  in  the 

installer  and  user

reference guide

.

Summary of Contents for RXYSQ6T7Y1B9

































Reviews: