background image

5 Installation

Installation and operation manual

8

RXYSQ6T7Y1B9

VRV IV-S system air conditioner

4P397285-1B – 2016.03

5.2

Mounting the outdoor unit

5.2.1

To provide the installation structure

Prepare  4  sets  of  anchor  bolts,  nuts  and  washers  (field  supply)  as
follows:

(mm)

>150

620

350

(345-355)

4× M12

a

a

Make sure not to cover the drain holes.

INFORMATION

The  recommended  height  of  the  upper  protruding  part  of
the bolts is 20 mm.

20

NOTICE

Fix the outdoor unit to the foundation bolts using nuts with
resin  washers  (a).  If  the  coating  on  the  fastening  area  is
stripped off, the nuts rust easily.

a

5.2.2

To install the outdoor unit

4× M12

5.2.3

To provide drainage

▪ Make sure that condensation water can be evacuated properly.

▪ Install  the  unit  on  a  base  to  make  sure  that  there  is  a  proper

drainage in order to avoid ice accumulation.

▪ Prepare a water drainage channel around the foundation to drain

waste water surrounding the unit.

▪ Avoid  drain  water  flowing  over  the  footpath,  so  that  it  does  not

become slippery in case of ambient freezing temperatures.

▪ If  you  install  the  unit  on  a  frame,  install  a  waterproof  plate  within

150  mm  of  the  bottom  side  of  the  unit  in  order  to  prevent  the
invasion of water in the unit and to avoid the drain water dripping
(see the following illustration).

NOTICE

If drain holes of the outdoor unit are covered by a mounting
base  or  by  floor  surface,  raise  the  unit  to  provide  a  free
space of more than 150 mm under the outdoor unit.

≥150 mm

Drain holes (dimensions in mm)

11

7

102

70

45

376

191

a

a

a

a

Drain holes

5.2.4

To prevent the outdoor unit from falling
over

1

Prepare  2  cables  as  indicated  in  the  following  illustration  (field
supply).

2

Place the 2 cables over the outdoor unit.

3

Insert  a  rubber  sheet  between  the  cables  and  the  outdoor  unit
to prevent the cable from scratching the paint (field supply).

4

Attach the cable’s ends. Tighten those ends.

5.3

Connecting the refrigerant piping

DANGER: RISK OF BURNING

Summary of Contents for RXYSQ6T7Y1B9

































Reviews: