background image

English

4

Installation Guidelines

• Where a wall or other obstacle is in the path of outdoor unit’s inlet or outlet airflow, follow the installation guidelines below.
• For any of the below installation patterns, the wall height on the outlet side should be 1200mm or less.

Precautions on Installation

• Check the strength and level of the installation ground so that the unit will not cause any operating vibration or noise after installed.
• In accordance with the foundation drawing, fix the unit securely by means of the foundation bolts. (Prepare 4 sets of M8 or M10 

foundation bolts, nuts and washers each which are available on the market.)

• It is best to screw in the foundation bolts until their length are 20mm from the foundation surface. 

Outdoor Unit Installation

1.

Installing outdoor unit

1) When installing the outdoor unit, refer to “Precautions for Selecting the Location” and the “Outdoor Unit Installation 

Drawings”.

2) If drain work is necessary, follow the procedures below.

2.

Drain work  

1) Use drain plug for drainage.
2) If the drain port is covered by a mounting base or floor surface, place 

additional foot bases of at least 30mm in height under the outdoor unit’s feet.

3) In cold areas, do not use a drain hose with the outdoor unit.  

(Otherwise, drain water may freeze, impairing heating performance.)

More than 50

More than 100

Side view

1200
or less

More than 50

More than 50

Top view

More 
than 100

Top view

unit: mm

More than 150

More than 300

More than 50

Wall facing one side

Walls facing two sides

Walls facing three sides

More than 150

20

Drain port

Bottom frame

Drain plug

Hose (available commercially,
inner dia. 16mm)

01_EN_3P254362-3E.fm  Page 4  Tuesday, December 7, 2010  7:32 PM

Summary of Contents for RXG25K2V1B

















Reviews: