background image

9

English

Wiring

 WARNING

• Do not use tapped wires, stranded wires, extension cords, or starburst connections, as they may cause overheating, electrical 

shock, or fire.

• Do not use locally purchased electrical parts inside the product. (Do not branch the power for the drain pump, etc., from the 

terminal block.) Doing so may cause electric shock or fire.

• Be sure to install an earth leak detector. (One that can handle higher harmonics.)

(This unit uses an inverter, which means that it must be used an earth leak detector capable handling harmonics in order to 
prevent malfunctioning of the earth leak detector itself.)

• Use an all-pole disconnection type breaker with at least 3mm between the contact point gaps.
• Do not connect the power wire to the indoor unit. Doing so may cause electric shock or fire.

• Equipment complying with EN/IEC 61000-3-12

(1)

• Do not turn ON the safety breaker until all work is completed.

1) Strip the insulation from the wire (20mm).
2) Connect the inter-unit wire between the indoor 

and outdoor units 

so that the terminal 

numbers match

. Tighten the terminal screws 

securely. We recommend a flathead 
screwdriver be used to tighten the screws. 

Appearance of outdoor units may differ from some models.

Observe the notes mentioned below when wiring to the power supply terminal block.
Precautions to be taken for power supply wiring.

(1)

European/International Technical Standard setting the limits for harmonic currents produced by equipment connected to public low-

voltage systems with input current >16 A and 

75 A per phase.

Safety 
breaker 
20A

Earth leakage 
circuit breaker

Earth

Inter-unit wire 
4-core 1.5mm² or more 
H05RN

Firmly fix the wires with 
the terminal screws.

Outdoor unit

Indoor 
unit

Power 
supply
50Hz 220-240V 

Firmly fix the wires with 
the terminal screws.

Power supply wire 
3-core 2.5mm² or more
H05RN

1

2

3

1

2

3

Power supply
terminal block

Shape wires so 
that the protection 
plate and conduit 
mounting plate fit 
securely.

Service lid

Screws

L

1

L

2

3PEN395501-1A.book  Page 9  Friday, July 24, 2015  1:53 PM

Summary of Contents for RX50KV1B
















Reviews: