background image

3

English

Accessories

1

Installation manual

A

This is at the bottom of the packaging.

1

Drain socket*

B

4

6

09/12 class

15/18/24 class

1

2

3

09/12 class

15/18/24 class

Drain cap (1)*

C

Drain cap (2)*

D

*Only for heat pump models.

Warranty

E

Precautions for Selecting a Location

1) 

Choose a place solid enough to bear the weight and vibration of the unit, where the operating sound will not be amplifi ed.

2) Choose a location where the hot air discharged from the unit or the operating sound will not cause a nuisance to the 

neighbors of the user.

3) Avoid locations, such as near bedrooms, where the operating sound may cause disturbance.
4) 

There must be suffi cient space to carry the unit into and out of the site.

5) 

There must be suffi cient space for air passage and no obstructions around the air inlet and the air outlet.

6) 

The site must not be prone to fl ammable gas leaks in the surrounding area.

7) Install units, power cords and inter-unit wire at least 10ft (3m) away from television and radio sets. (This is to prevent 

interference to images and sounds. Noise may be produced even if they are more than 10ft (3m) away depending on radio 
wave conditions.)

8) In coastal areas or other places with a salty atmosphere or one containing sulfate gas, corrosion may shorten the life of the air 

conditioner.

9) 

Since water will fl ow from the drain of the outdoor unit, do not place under the unit anything which must be kept away from 

moisture.

NOTE

Cannot be installed suspended from a ceiling or stacked.

CAUTION

When operating the air conditioner in a low outdoor ambient temperature, be sure to 
follow the instructions described below.

• 

To prevent exposure to wind, install the outdoor unit with its suction side facing the 
wall.

• 

Never install the outdoor unit at a site where the suction side may be exposed 
directly to wind.

•  To prevent exposure to wind, it is recommended to install a baffl e plate on the air 

discharge side of the outdoor unit.

• 

In heavy snow areas, select an installation site where the snow will not affect the unit.

• 

If there is a likelihood of snow accumulating on the outdoor unit, attach a snow 
protection hood.

• 

In high humidity areas or heavy snow areas, it is recommended to attach a drain pan 
heater to prevent ice build-up from the bottom frame.

• 

Construct a large canopy.

• 

Construct a pedestal.

Install the unit high enough off 
the ground to prevent burying 
in snow.

01_EN_3P379970-6B.indd   3

11/13/2015   15:48:24

Summary of Contents for RX09NMVJU















Reviews: