manualshive.com logo in svg

Daikin RMXS-L Series, Service Manual

Share
Download
Daikin RMXS-L Series Service Manual Download Page 205

SiUS181305E

Troubleshooting for Outdoor Unit

Troubleshooting

196

7.11 Suction Pipe Thermistor (R3T, R5T) Abnormality

Error Code

J5

Method of Error 
Detection

The temperature detected by the suction pipe thermistor determines the error.

Error Decision 
Conditions

When a short circuit or an open circuit in the suction pipe thermistor is detected

Supposed 
Causes

Disconnection of thermistor

Defective suction pipe thermistor (R3T, R5T)

Defective main PCB (A1P)

Troubleshooting

Refer to Thermistor Resistance / Temperature Characteristics table 1 on page 224.

Refer to page 139 for detail about monitor mode.

Is the thermistor 

ASSY connected to 

X12A on the main PCB 

(A1P)?

Is the 

resistance 

normal when 

measured after 

disconnecting the 

thermistor (R3T, 
R5T)? (3.5 k

Ω 

~ 

360 k

Ω

)

Replace the main PCB 
(A1P).

(R18082)

Connect the thermistor and 
turn on again.

NO

Replace the defective 
thermistor (R3T, R5T).

NO

YES

YES

Identify the defective 
thermistor (R3T or R5T) in 
monitor mode.

Caution

Be sure to turn off the power switch before connecting or disconnecting 
connectors, or parts may be damaged.

Summary of Contents for RMXS-L Series



























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands