background image

3

English

Outdoor Unit Installation Drawings

Precautions on Installation

• Check the strength and level of the installation ground so that the unit will not cause any operating vibration or noise after installed.
• In accordance with the foundation drawing, fix the unit securely by means of the foundation bolts. (Prepare four sets of M8 or M10 

foundation bolts, nuts and washers each which are available on the market.)

• It is best to screw in the foundation bolts until their length are 20mm from the foundation surface.

Max. allowable height

Min. allowable length

Max. allowable length

30m

1.5m

20m

Liquid pipe

Gas pipe

O.D.  6.4mm

O.D. 15.9mm

20g/m

Additional refrigerant 
required for refrigerant 
pipe exceeding 10m 
in length.

*

 Be sure to add the proper amount of additional refrigerant.

   Failure to do so may result in reduced performance.

The suggested shortest pipe length is 1.5 m, in order to avoid 

noise from the outdoor unit and vibration. 

(Mechanical noise and vibration may occur depending on how 

the unit is installed and the environment in which it is used.)

25cm from w

all

Right side plate

35cm

(F

oot bolt-hole 

 centres)

(Foot bolt-hole centres)

62cm

**

**

*

CAUTION

** Set the piping length 

from 1.5m to 30m.

Wrap the insulation 
pipe with the finishing 
tape from bottom to top.

Allow space for piping 
and electrical servicing.

Allow 30cm of work 
space below the 
ceiling surface.

If there is the danger of the unit falling 
or overturning, fix the unit with 
foundation bolts, or with wire or other 
means.

If the location does not have good 
drainage, place the unit on a level 
mounting base (or a plastic pedestal). 
Install the outdoor unit in a level 
position. Failure to do so may result in 
water leakage or accumulation.

Level mounting base 
(available separately)

Clamping material

Insulation tube

Service lid

Tape

Also insulate the connection on the outdoor unit.

Use tape or insulating material on all connections 
to prevent air from getting in between the copper 
piping and the insulation tube.
Be sure to do this if the outdoor unit is installed 
above.

20

3PEN188780-2R.book  Page 3  Wednesday, March 16, 2016  3:46 PM

Summary of Contents for RKS71FAV1B

















Reviews: