background image

3

3P362438-9N English

1 .3 .  Indoor capacity range

1 .3 .1 .  Combination Ratio

Combination Ratio = Total capacity index of the indoor units / Capac

-

ity index of the outdoor units

Type

Min. combination ratio

Types of connected outdoor units

 REYQ-T type

Single outdoor units

50% (*1)

Double outdoor units

Triple outdoor units

*1. 70% : REYQ72T type

Type

Max. combination ratio

Types of connected indoor units

When using only

FXDQ, FXMQ-P,

FXAQ

When using only

 FXTQ, (CXTQ), 

 

or at least one

FXFQ07/09

All other models

Single outdoor units

200% (*1)

130%

200% (*1)

Double outdoor units

160% (*1)

Triple outdoor units

130%

*1. If the operational capacity of indoor units is more than 130%, low 

airflow operation is enforced in all the indoor units.

1 .3 .2 .  Outdoor Unit Combinations

Total capacity of indoor units needs to be within the specified range.
REYQ-T type

<Outdoor unit>

<Total capacity index of indoor units>

REYQ72TAYC

*

. . . . . . . . . . . . . . . . . . . .  . 

36-93

REYQ96TAYC

*

. . . . . . . . . . . . . . . . . . . .  .  48-124

REYQ120TAYC

*

. . . . . . . . . . . . . . . . . . . .  .  60-156

REYQ144TAYC

*

. . . . . . . . . . . . . . . . . . . .  .  72-187

REYQ168TAYC

*

. . . . . . . . . . . . . . . . . . . .  .  84-218

REYQ192TAYC

*

. . . . . . . . . . . . . . . . . . . .  .  96-249

REYQ216TAYC

*

. . . . . . . . . . . . . . . . . . . .  .  108-280

REYQ240TAYC

*

. . . . . . . . . . . . . . . . . . . .  .  120-312

REYQ264TAYC

*

. . . . . . . . . . . . . . . . . . . .  .  132-343

REYQ288TAYC

*

. . . . . . . . . . . . . . . . . . . .  .  144-374

REYQ312TAYC

*

. . . . . . . . . . . . . . . . . . . .  .  156-405

REYQ336TAYC

*

. . . . . . . . . . . . . . . . . . . .  .  168-436

REYQ360TAYC

*

. . . . . . . . . . . . . . . . . . . .  .  180-468

REYQ384TAYC

*

. . . . . . . . . . . . . . . . . . . .  .  192-499

 NOTE

Higher capacity than the above table can be selected, this may affect 
heating and cooling capacity. For additional information see technical 
engineering data.

1 .4 .  Scope of the manual

This manual describes the procedures for handling, installing and 

connecting the VRV IV REYQ-T series outdoor units. This manual has 

been prepared to ensure adequate maintenance of the unit, and it will 
provide help in case problems occur.

 INFORMATION

The installation of the indoor unit(s) is described in the indoor unit 
installation manual provided with the indoor unit(s).

2 .  Accessories

2 .1 .  Accessories supplied with this unit

Confirm the following accessories are included. The storage location 
of the accessories is shown in the figure below.

Accessories assy (piping)

Accessories assy (operation 

and installation manual)

 NOTE

Do not throw away any of the accessories until installation is complete. 
They are needed for installation work.

Name

Clamp (1)

Clamp (2)

Clamp (3)

Vinyl tube

Manuals, etc.

Quantity

7 pcs.

1 pc.

1 pc.

5 pcs.

1 pc. each

Shape

(Small)

(Large)

• 

Operation Manual

• 

Installation Manual

•  REQUEST FOR THE 

INDICATION label  
(Installation records)

Name

Liquid side 

accessory 

pipe (1)

Liquid side 

accessory 

pipe (2)

Gas side  

accessory 

pipe (1)

Gas side  

accessory 

pipe (2)

Quantity

1 pc.

1 pc.

1 pc.

1 pc.

Shape

168T

72-144T

72,120T

144,168T

96T

96,144,168T

120T

72T

Name

High and low gas 

side accessory 

pipe (1)

High and low gas 

side accessory 

pipe (2)

L type  

accessory joint

Quantity

1 pc.

1 pc.

2 pcs.

Shape

96-168T

72T

72,96T

120-168T

01_EN_3P362438-9N.indb   3

12/11/2019   2:35:24 PM

Summary of Contents for REYQ72TAYC Series















































Reviews: