background image

IM 1272 • OPTILINE VERTICAL FAN COILS 26 www.DaikinApplied.com

Addendum

Table 7: Engineer Mode Menu Item Descriptions

Item

Mnemonic

Description

°C Type

°F Type

Step

Default

Range

Default

Range

E1

db

Dead band offset

2.0

0~10.0

7.0

0~18.0

0.5 (°C/°F)

E2

ESIC

Unoccupied (ESI) Cooling  

Set Point

28.0

25.0~35.0

82.0

77.0~95.0

1.0(°C/°F)

E3

ESIH

Unoccupied (ESI) Heating  

Set Point

15.0

10.0~22.0

59.0

50.0~72.0

1.0(°C/°F)

E4

I-t

Integral Time and Output  

Cycle Time

90

10~500

90

10-500

10 (Sec.)

E5

AO1L

Not used

E6

AO1H

Not used

E7

AO2L

Analog Output 2 Low Adjustment 

(for FAN control)

0

0~125

0

0~125

1(~0.044V)

E8

AO2H

Analog Output 2 High Adjustment 

(for FAN control)

-25

-150~0

-25

-150~0

1(~0.044V)

E9

SP-L

Low Limit for Temperature  

Set Point

10.0

0~50.0

50.0

32.0~122.0

1.0 (°C/°F)

E10

SP-H

High Limit for Temperature  

Set Point

35.0

0~50.0

95.0

32.0~122.0

1.0 (°C/°F)

E11

OFSt

Current Temperature Offset

0.0

-10.0~10.0

0.0

-18.0~18.0

0.1(°C/°F)

E12

Pb

Proportional Band or Stage Width

2.0

0~10.0

3.6

0~18.0

0.1 (°C/°F)

E13

LOC

Bit Definition — 

Bit 0: Mode Button 

1: Down Buttons 

2: Up Button 

3: Fan Button 

4: Power Button 

5: Set Button 

6: ESI Contact Detection 

7: Reserved

*Bit Value
0: Unlock/enable

1: Lock/disable

Examples:

0 – Unlock/enable all

1 – Lock MODE Button

2 – Lock Down Button

8 – Lock Fan Button

15 – Lock MODE & Down & Up & 

Fan SPEED Buttons

16 –  LockPower Button

64 – Disable ESI contact 

detection

255 – Lock/disable all

0

0–255

0

0–255

1

E14

ESI

ESI Contact Definition

0

0~1

0

0~1

0: N.O. 

1: N.C.

E15

rS

Present Temperature is Getting 

from Built-In Temperature Sensor, 

or Remote Temperature Sensor

0

0~1

0

0~1

0: built-in 

1: remote

E16

-SP-

Display Present Value of 

Temperature or Set Point for 

Normal Displaying

0

0–1

0

0–1

0: display PV 

1: display SP

E17

FAnL

Lowest Fan Speed in Continuous 

Fan Mode

25

0~100

25

0~100

1(%)

E18

Fan2

Medium Fan Speed

60

20~100

60

20~100

1(%)

E19

dLAy

Minimum delay time between 

cooling and heating

0

0~5

0

0~5

1 (minute)

E20

dirC

Cooling Valve N.C./N.O. Setting

1

0~1

1

0~1

0: N.O. 

1: N.C.

Summary of Contents for OptiLine FSG





























Reviews: